TechniSat DIGITY CI Operating Manual manual Saving satellite positions, List of current satellites

Page 38

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 38

(Fig. 8-13)

(Fig. 8-14)

(Fig. 8-15)

(Fig. 8-16)

(Fig. 8-17)

>Now use the arrow keys left (Field East will be marked) resp. right (Field West will be marked) to rotate the dish antenna to the required position. Simply keep the respective key depressed until the correct position is achieved.

8.3.2.3 Automatic fine adjustment (Autofocus)

You should carry out an automatic focussing procedure before saving the satellite position to memory. This will adjust the antenna to optimum reception by instrument means.

>Press the yellow function key (Actions) to open the window listing the available actions.

Use the arrow keys up/down to mark the item

Autofocus.

>Confirm by pressing OK.

>Press the green function key (Autofocus) to start the procedure.

The message Autofocus will be displayed while the procedure is in progress (Fig. 8-13)

8.3.3 Saving satellite positions

When the autofocus procedure has been completed, you must still save the satellite position to memory.

>Use the arrow keys to mark the field Save.

>Confirm by pressing OK.

The test transponder selected will now be used to check whether a signal is being received at this positi- on. The function will also check whether there is a pre- programmed position in memory at this orbital position. (Fig. 8-14)

If this is the case, the message : Orbital position xx identified. Save satellite? (Fig. 8-15)

>To save the satellite position to memory, use the arrow keys left/right to mark the field Yes, and confirm by pressing OK.

If the check procedure of the test transponder does not identify any of the pre-programmed positions stored in memory, or if the signal received is too weak, this information will be displayed on screen. (Figs. 8- 16 and 8-17)

>To save the satellite position in memory, use the arrow keys left/right to mark the field Yes and confirm by pressing OK.

8.4 List of current satellites

The satellite positions saved will be found in the satellite list. Positions not yet saved will be indicated by “*” .

>To rotate the dish antenna to one of the positions on the list, use the arrow keys to mark the item Current satellite list.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents
Digity CI Contents BedanlDIGITY CIQuark3en.qxd 31.01.03 1647 Seite Remote control IllustrationsFront panel Rear panelPlease read this first Important operating informationEnvironmental note Safety NoteWhen not in operation VCR External unit Mains power connectionConnections Connection to a television setHi-fi amplifier InstallationBasic settings Serial interface RSTime difference GMT hours Audio/Video settingsParental control CountryScart mode LNB setting/Adjusting to external unit/Satellite selectionLanguage Audio signal Image format TV setMenu LNB Settings Switching DiSEqC on and offSetting the switching matrix and the LNB characteristics Additional Settings Programme selection Switching on and offOperation Calling up blocked programmes Using the programme listSelecting a list Information box Volume controlReception of encrypted programmes Time control Near Video On Demand Selecting a different languageMultifeed options Display clock and programme information Switching between TV and RadioReturn to previous programme Additional programme informationTransponder Information Electronic Programme GuideProgramming via EPG TimerManual programming/Changing timer set- tings VCR Video text Using the video text decoder of your television setUsing the internal video text decoder PreselectAdding programmes to the programme list Changing basic programmingCalling up the programme list Deleting from the Total list Deleting programmesDeleting from the Favourites list Use the arrow keys left/right to select Yes or NoKeys up/down or the numeric keys Blocking access to programmes parental controlSorting programmes Changing the PIN Unblocking access control for individual programmesSettings Programme Search SatelliteTransponder Manual search Integrating programmes after a searchActivating default setting Restoring basic programming/ Delete allUse the arrow keys left/right to indicate Yes or Abort Delete all programmesUpdating software Operation in conjunction with a rotary Antenna System configurationEncryption system Eastern and Western limitsUse the arrow keys left/right to mark the item LNB test Setting Eastern limitSetting Western limit Use the arrow keys up/down to mark the item Delete limitsGeo-positioning Press the arrow key leftSetting the satellite position Setting user-defined satellite positions User SatelliteAntenna manual adjustment Adjusting the satellite antennaTest-Transponder/LNB-configuration List of current satellites Automatic fine adjustment AutofocusSaving satellite positions Selecting a satellite position Deleting a satellite positionReference position Technical Terms DVBLOF Scart Technical data FECTV-SCART Trouble-shooting guide Dear customerProblem Possible cause Solution Annexure Co-ordinates of selected German cities City Geogr. Longitude E Geogr. Latitude NCo-ordinates of selected German cities City Geogr. LongitudeE Geogr. Latitude N TV/radio switching For everyday use