TechniSat DIGITY CI Operating Manual manual Setting the satellite position

Page 36

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 36

(Fig. 8-10)

(Fig. 8-11)

In the menu, enter the value for geographical latitude as a decimal value correct to one decimal place (50,2) .

The decimal equivalent of the longitude can be calculated in the same way.

8.3 Setting the satellite position

Work progressively through points 8.3.1 to 8.3.3 for each of the satellite positions to be entered. We recommend that you start by programming the most easterly satellite first. Then proceed to enter each additional satellite position, working in a westerly direction, until you reach the most westerly satellite position.

Your receiver is programmed at the factory for the most com- mon satellite positions. In addition you can enter and configu- re user-defined satellite positions for any orbital position (User 1 to User 14 ).

8.3.1 Selecting satellite positions

8.3.1.1Selecting a pre-programmed satellite position

>To enter a satellite position in the satellite list, use the arrow keys to mark the field Sat new.

>Confirm by pressingt OK.

A list of all available satellite positions will be displayed. (Fig. 8-10)

>Use the arrow keys up/down to mark a satellite position that you wish to include in the satellite list.

>Press the OK key to accept the selection into the list. In the position Geo-positioningon (Point 8.2) the dish antenna will now be automatically rotated to the programmed satellite position. The rotation procedure is indicated by a blinking message “rotating”.

In the position Geo-positioning off you will have to rotate the antenna manually to the desired satellite position (Point 8.3.2.2).

8.3.1.2Setting user-defined satellite positions (User Satellite)

>To accept a satellite position into the satellite list, use the arrow keys to mark the field Sat new.

>Confirm by pressing OK.

A list of the available satellite positions will be displayed. (Fig. 8-11)

>Use the arrow keys up/down to mark a user-defined satellite position (User 1 to User 14).

>Press the OK key to display the menu for setting a test transponder. In this menu, set the parameters of the test transponder as well as of the LNB used, as described in Point 5.4.3 .

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents
Digity CI Contents BedanlDIGITY CIQuark3en.qxd 31.01.03 1647 Seite Remote control IllustrationsFront panel Rear panelPlease read this first Important operating informationSafety Note When not in operationEnvironmental note VCR Mains power connection ConnectionsExternal unit Connection to a television setInstallation Basic settingsHi-fi amplifier Serial interface RSAudio/Video settings Parental controlTime difference GMT hours CountryLNB setting/Adjusting to external unit/Satellite selection Language Audio signalScart mode Image format TV setSwitching DiSEqC on and off Setting the switching matrix and the LNB characteristicsMenu LNB Settings Additional Settings Switching on and off OperationProgramme selection Using the programme list Selecting a listCalling up blocked programmes Volume control Reception of encrypted programmesInformation box Selecting a different language Multifeed optionsTime control Near Video On Demand Switching between TV and Radio Return to previous programmeDisplay clock and programme information Additional programme informationTransponder Information Electronic Programme GuideTimer Manual programming/Changing timer set- tingsProgramming via EPG VCR Using the video text decoder of your television set Using the internal video text decoderVideo text PreselectChanging basic programming Calling up the programme listAdding programmes to the programme list Deleting programmes Deleting from the Favourites listDeleting from the Total list Use the arrow keys left/right to select Yes or NoBlocking access to programmes parental control Sorting programmesKeys up/down or the numeric keys Unblocking access control for individual programmes SettingsChanging the PIN Programme Search SatelliteTransponder Manual search Integrating programmes after a searchActivating default setting Restoring basic programming/ Delete allDelete all programmes Updating softwareUse the arrow keys left/right to indicate Yes or Abort System configuration Encryption systemOperation in conjunction with a rotary Antenna Eastern and Western limitsSetting Eastern limit Setting Western limitUse the arrow keys left/right to mark the item LNB test Use the arrow keys up/down to mark the item Delete limitsGeo-positioning Press the arrow key leftSetting the satellite position Setting user-defined satellite positions User SatelliteAdjusting the satellite antenna Test-Transponder/LNB-configurationAntenna manual adjustment Automatic fine adjustment Autofocus Saving satellite positionsList of current satellites Deleting a satellite position Reference positionSelecting a satellite position Technical Terms DVBLOF Scart Technical data FECTV-SCART Trouble-shooting guide Dear customerProblem Possible cause Solution Annexure Co-ordinates of selected German cities City Geogr. Longitude E Geogr. Latitude NCo-ordinates of selected German cities City Geogr. LongitudeE Geogr. Latitude N TV/radio switching For everyday use