TechniSat DIGITY CI Operating Manual manual Switching DiSEqC on and off, Menu LNB Settings

Page 13

bed_anl_DIGITY CI_Quark3_en.qxd 31.01.03 16:47 Seite 13

>Confirm by pressing OK. The menu LNB Settings will be displayed. (Fig. 5-8)

The following settings can be effected in this sub-menu:

5.4.1 Switching DiSEqC on and off

DiSEqC (Digital Satelliten Equipment Control) is a digital switching signal used to control DiSEqC-compatible components via the antenna connection.

If your external unit is equipped with DiSEqC componen ts you must activate the DiSEqC switching:

>In this line, use the OK key to switch the DiSEqC on or off.

As only one LNB can be controlled when the DiSEqC switching is not activated, the menu will be restricted to the configuration of a single LNB.

5.4.2Setting the switching matrix and the LNB characteristics

The menu lists the four switching criteria of the DiSEqC switching feature.

Your unit is pre-programmed so that ASTRA will be received in switch position A/A and Eutelsat will be received on switch position B/A of a multi-switch. Should the switching matrix of your receiving installation be configured differently, or if you wish to receive other satellites, you can adjust your receiver to the parameters of your receiving installation as follows.

>Use the arrow keys up/down to select the DiSEqC switch position (1-4) to which you wish to assign a satellite, by marking this line in blue (e.g.. A/B 3 No Satellite).

>Press OK.

A table showing the satellites available for selection will be displayed.

>Use the arrow keys up/down to mark the required satellite.

Use the arrow keys up/down to move up or down the menu one line at a time, use the arrow keys left/right to move forward or back one page at a time.

Should the satellite you require not be listed, please select one of the reserve slots, designated User1 to

User 14.

>Confirm by pressing OK. The selected satellite will now be inserted at the previously marked poosition in

the menu LNB Settings.

You should now proceed to work through the menu LNB Settings, until the settings in this menu correspond with the characteristics of your receiving installation. In the case of any switching criteria you do not require, select the option No Satellite.

Example:

A B

Position

Output

A B

Option

Output

(Fig. 5-8)

A B

Position

Output

13

Image 13

Contents Digity CI Contents BedanlDIGITY CIQuark3en.qxd 31.01.03 1647 Seite Illustrations Remote controlRear panel Front panelImportant operating information Please read this firstWhen not in operation Safety NoteEnvironmental note VCR Connections Mains power connectionExternal unit Connection to a television setBasic settings InstallationHi-fi amplifier Serial interface RSParental control Audio/Video settingsTime difference GMT hours CountryLanguage Audio signal LNB setting/Adjusting to external unit/Satellite selectionScart mode Image format TV setSetting the switching matrix and the LNB characteristics Switching DiSEqC on and offMenu LNB Settings Additional Settings Operation Switching on and offProgramme selection Selecting a list Using the programme listCalling up blocked programmes Reception of encrypted programmes Volume controlInformation box Multifeed options Selecting a different languageTime control Near Video On Demand Return to previous programme Switching between TV and RadioDisplay clock and programme information Additional programme informationElectronic Programme Guide Transponder InformationManual programming/Changing timer set- tings TimerProgramming via EPG VCR Using the internal video text decoder Using the video text decoder of your television setVideo text PreselectCalling up the programme list Changing basic programmingAdding programmes to the programme list Deleting from the Favourites list Deleting programmesDeleting from the Total list Use the arrow keys left/right to select Yes or NoSorting programmes Blocking access to programmes parental controlKeys up/down or the numeric keys Settings Unblocking access control for individual programmesChanging the PIN Satellite Programme SearchTransponder Integrating programmes after a search Manual searchRestoring basic programming/ Delete all Activating default settingUpdating software Delete all programmesUse the arrow keys left/right to indicate Yes or Abort Encryption system System configurationOperation in conjunction with a rotary Antenna Eastern and Western limitsSetting Western limit Setting Eastern limitUse the arrow keys left/right to mark the item LNB test Use the arrow keys up/down to mark the item Delete limitsPress the arrow key left Geo-positioningSetting user-defined satellite positions User Satellite Setting the satellite positionTest-Transponder/LNB-configuration Adjusting the satellite antennaAntenna manual adjustment Saving satellite positions Automatic fine adjustment AutofocusList of current satellites Reference position Deleting a satellite positionSelecting a satellite position DVB Technical TermsLOF Scart FEC Technical dataTV-SCART Dear customer Trouble-shooting guideProblem Possible cause Solution City Geogr. Longitude E Geogr. Latitude N Annexure Co-ordinates of selected German citiesCo-ordinates of selected German cities City Geogr. LongitudeE Geogr. Latitude N For everyday use TV/radio switching