Tandberg Data 7000 manual Unpacking the Base, Unpacking and Installing the Monitor Rack

Page 14

Installation	TANDBERG Videoconferencing System

Unpacking the Base

Due to the weight of the system, the base should be placed in its permanent location as soon as it is unpacked.

NOTE

IF THE SYSTEM IS TO BE PLACED AGAINST A WALL, IT IS POSSIBLE TO REDUCE THE SIZE OF THE BOTTOM PLATE. THE REDUCTION SHOULD BE DONE BEFORE THE REST OF THE INSTALLATION IS CARRIED OUT.

Unpacking and Installing the Monitor Rack

Lift the Monitor Rack out of the box. Do not remove the straps or packaging that are around the rack. Place the rack on top of the base. Make sure that the cables from the base do not get stuck in between.

You will find 4 bolts sticking out at the rear end of the base. Use the 4 nuts to fasten the Monitor Rack in place. You can now remove the straps and packaging from the Monitor Rack.

NOTE

THE FRONT COVER IS MADE WITH PLASTIC AND SHOULD BE TREATED WITH CARE.

Carefully flip down the plastic cover. 4 hexagonal-shaped screws should be used to secure the Monitor Rack to the top of the Base. There are 2 holes located on each side.

14

Image 14

Contents UserManual Plasma Monitors Environmental Issues Trademarks and copyrightOperator Safety Summary Contents Appendices 108 Index 116 Advanced usePeripheral Equipment Introduction TIPMenu structure LANTandberg 7000 Videoconferencing System At a glance the Tandberg 7000 systemCodec V.E. CameraMonitors Remote control Table microphone Tandberg Natural Audio moduleUnpacking InstallationPrecautions Unpacking and Installing the Monitor Rack Unpacking the BaseInstalling the camera InstallingInstalling the monitors Connecting cables Securing the cables Monitor configurationLAN cable Attaching the back coversSystem configuration MenuIsdn configuration LAN configuration Welcome menu Getting startedSystem start-up Basics Making and ending calls Making a callTIP Selecting / setting default quality bandwidth Selecting / setting default network Correcting keying mistakes Answer a callEnd a call Directory Press D Irectory to bring up the following menuDelete Entry Add New EntryEdit Entry Add MultiSite Entry Add SiteView outgoing video selfview Adjusting volumeGeneral use Microphone on/offDo Not Disturb / Sleep Mode Selecting video sources Focusing cameraControlling the Main Camera Moving / zooming cameraVoice Activated Camera Positioning Storing presets PresetsSelecting presets Far end camera control Fecc Main cam Aux Doc cam VcrViewing a still image Sending/receiving still imagesSending a still image Receiving a still imageDuo Video Add Duo VideoEnd a Duo Video call MultiSite MCU Establishing MultiSite meetings using Directory MultiSite cascadingAdding an extra site dial out Press C OnnectDisconnecting sites from a conference Adding an extra site dialPC Presenter PC SoftPresenterWeb-interface Text Chat / Closed CaptioningStreaming Advanced use Main menuAudio VGA ResolutionsCall quality VideoAdvanced call quality 4CIFPresentations Presentation ModeDuo Video Mode Duo Video QualityAuto-display still image Duo Video NumberDuo Video / Still Image source Still image filterFar end camera control UtilitiesAutoanswer Dual MonitorContinuous Presence Auto-PIPWelcome Menu MCU status lineMCU services Quick Menu Terminal Names Request floorRelease floor View site #Chair control Audio Settings Audio InputsPage Audio Outputs Echo Control Page Automatic Gain Control AGC Settings Alert Tones & Volume Restore Audio DefaultsDocument Camera Video SettingsCamera Tracking Mode Whitebalance FocusBrightness Video NameVGA Settings VNC Settings Terminal Settings Network ConfigurationPage ISDN-BRI Settings CoreIsdn BRI This Service has Limited Access on Some Isdn Networks Parallel dial ISDN-PRI Settings Channels automatically Page PRISM1, PRISMII, Wats Leased E1/T1 Settings External network settings 35/RS-366 cable LAN Settings Page Settings Advanced H.323 Settings RsvpNAT IP Settings Snmp Settings Incoming MCU calls Call SettingsAccess Code Incoming telephone callsNetwork Profiles EncryptionMax Call Length Dataport configuration Page Language Software OptionsChannel status DiagnosticsSystem info TIP Restore defaults Call statusView current settings Test subsystemPeripheral Equipment InterfacesPage Dual Monitor Document camera Multiple controllable cameras AudioScience microphone TrackerVCR Recording Video Cassette Recorder VCRVCR Playback Telephone Add-On Extra fixed camerasPC applications Additional microphones Appendices Appendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapterAppendix 3 Connecting the system to PRI/T1 Using CSU adapterIris control and lighting Loudspeaker volumeAppendix 4 Environmental considerations BackgroundGuidelines for setting up videoconferencing rooms How to prepare a typical room for videoconferencingAppendix 5 Using the file system Appendix 6 Access Code ABCAppendix 7 Declaration of Conformity Index Tandberg Videoconferencing System Index To use the dataport for PC applications