Tandberg Data 7000 manual System configuration, Menu

Page 18

Installation	TANDBERG Videoconferencing System

System configuration

•Switch the system on by activating the power switch on the codec (located on the right hand side at the rear of the codec). A green light is shown (located in the center on the front of the codec).

•After the system has performed a self-test routine, product logo and a ‘Welcome’ menu will be displayed on the monitor.

NOTE

THESE SETTINGS ARE ESSENTIAL FOR OPTIMAL SYSTEM SET-UP.

•Enabled but unused ISDN lines (lines not active) should be disabled. Select the Quick Key ‘System Info’ (on the remote control) to view line status.

menu

PRESS MENU ON THE REMOTE CONTROL. SELECT THE MENU ‘TERMINAL SETTINGS’, ‘NETWORK’, ‘ISDN-BRISETTINGS’. SELECT THE RELEVANT ‘LINE SETUP’ MENU AND SET ‘ENABLED: OFF’.

•Enter System Name to identify the system during an MCU conference. Select ‘Utilities’, ‘System Name’ and enter the name using the number keys (as on a mobile phone).

•Select the language you want to use in ‘Terminal Settings’, ‘Language’.

•If you are using two monitors, set ‘Utilities’, ‘Dual Monitor: On’.

•To activate MultiSite and/or Presenter, enter an option key (see paperwork accompanying your system), see

‘Terminal Settings’, ‘Software Options’.

connect • Press CONNECT on the remote control. A dial tone should be heard if the network is active.

• Using the monitor remote control, adjust the volume on the monitor to a level of your choice. This volume will be the default volume for all calls.

18

Image 18

Contents UserManual Plasma Monitors Environmental Issues Trademarks and copyrightOperator Safety Summary Contents Advanced use Peripheral EquipmentAppendices 108 Index 116 Introduction TIPMenu structure LANTandberg 7000 Videoconferencing System At a glance the Tandberg 7000 systemV.E. Camera MonitorsCodec Remote control Table microphone Tandberg Natural Audio moduleInstallation PrecautionsUnpacking Unpacking and Installing the Monitor Rack Unpacking the BaseInstalling Installing the monitorsInstalling the camera Connecting cables Securing the cables Monitor configurationLAN cable Attaching the back coversSystem configuration MenuIsdn configuration LAN configuration Getting started System start-upWelcome menu Basics Making and ending calls Making a callTIP Selecting / setting default quality bandwidth Selecting / setting default network Answer a call End a callCorrecting keying mistakes Directory Press D Irectory to bring up the following menuAdd New Entry Edit EntryDelete Entry Add MultiSite Entry Add SiteView outgoing video selfview Adjusting volumeGeneral use Microphone on/offDo Not Disturb / Sleep Mode Selecting video sources Focusing cameraControlling the Main Camera Moving / zooming cameraVoice Activated Camera Positioning Presets Selecting presetsStoring presets Far end camera control Fecc Main cam Aux Doc cam VcrViewing a still image Sending/receiving still imagesSending a still image Receiving a still imageDuo Video Add Duo VideoEnd a Duo Video call MultiSite MCU Establishing MultiSite meetings using Directory MultiSite cascadingAdding an extra site dial out Press C OnnectDisconnecting sites from a conference Adding an extra site dialPC Presenter PC SoftPresenterWeb-interface Text Chat / Closed CaptioningStreaming Advanced use Main menuAudio VGA ResolutionsCall quality VideoAdvanced call quality 4CIFPresentations Presentation ModeDuo Video Mode Duo Video QualityAuto-display still image Duo Video NumberDuo Video / Still Image source Still image filterFar end camera control UtilitiesAutoanswer Dual MonitorContinuous Presence Auto-PIPWelcome Menu MCU status lineMCU services Quick Menu Terminal Names Request floorRelease floor View site #Chair control Audio Settings Audio InputsPage Audio Outputs Echo Control Page Automatic Gain Control AGC Settings Alert Tones & Volume Restore Audio DefaultsVideo Settings Camera Tracking ModeDocument Camera Whitebalance FocusBrightness Video NameVGA Settings VNC Settings Terminal Settings Network ConfigurationPage ISDN-BRI Settings CoreIsdn BRI This Service has Limited Access on Some Isdn Networks Parallel dial ISDN-PRI Settings Channels automatically Page PRISM1, PRISMII, Wats Leased E1/T1 Settings External network settings 35/RS-366 cable LAN Settings Page Settings Advanced H.323 Settings RsvpNAT IP Settings Snmp Settings Incoming MCU calls Call SettingsAccess Code Incoming telephone callsEncryption Max Call LengthNetwork Profiles Dataport configuration Page Language Software OptionsDiagnostics System infoChannel status TIP Restore defaults Call statusView current settings Test subsystemPeripheral Equipment InterfacesPage Dual Monitor Document camera Multiple controllable cameras AudioScience microphone TrackerVideo Cassette Recorder VCR VCR PlaybackVCR Recording Telephone Add-On Extra fixed camerasPC applications Additional microphones Appendices Appendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapterAppendix 3 Connecting the system to PRI/T1 Using CSU adapterIris control and lighting Loudspeaker volumeAppendix 4 Environmental considerations BackgroundGuidelines for setting up videoconferencing rooms How to prepare a typical room for videoconferencingAppendix 5 Using the file system Appendix 6 Access Code ABCAppendix 7 Declaration of Conformity Index Tandberg Videoconferencing System Index To use the dataport for PC applications