Tandberg Data 7000 manual VNC Settings

Page 68

Advanced use

TANDBERG Videoconferencing System

VNC Settings

NOTE VNC SERVER SOFTWARE SETUP

• BOTH THE PC AND THE VIDEOCONFERENCING SYSTEM MUST BE CONNECTED TO THE LAN.

• A VNC SERVER MUST BE INSTALLED ON THE PC. FREE SOFTWARE CAN BE

DOWNLOADED FROM HTTP://WWW.UK.RESEARCH.ATT.COM/VNC

• INSTALL THE SOFTWARE BY RUNNING THE DOWNLOADED FILE.

• TO CONFIGURE THE VNC SERVER SOFTWARE :

• SELECT “ACCEPT SOCKET CONNECTIONS”.

• SELECT “AUTO” FOR “DISPLAY NUMBER”. ‘DISPLAY NUMBER’ IN THE SYSTEM MUST THEN HAVE THE VALUE 0.

• ENTER A PASSWORD IN THE “PASSWORD”-FIELD. MUST CORRESPOND WITH

THE ‘VNC SETTINGS’ ON YOUR SYSTEM.

Address

The IP-address of the PC with the VNC software installed. To find the IP-address of the PC, select ‘Command Prompt’ from the Startup-menu. Type ‘ipconfig’ and press ENTER.

Display Number

The display number for VNC is 0 and upwards. If you are using WinVNC, double-click on the icon on the toolbar to view ‘WinVNC properties’. This number should correspond with ‘Display Number’ in this menu.

Password

Enter the same password as specified in WinVNC properties. The password will be shown as asterisk signs (*) the next time you enter the menu.

Start using VNC

To activate VNC, press ‘PC’ on the remote control. Please make sure that ‘PC’ is set to ‘VNC’ in the ‘Video Settings Menu’. See also ‘PC SoftPresenter’ section for further information.

68

Image 68

Contents UserManual Plasma Monitors Environmental Issues Trademarks and copyrightOperator Safety Summary Contents Appendices 108 Index 116 Advanced usePeripheral Equipment Introduction TIPMenu structure LANTandberg 7000 Videoconferencing System At a glance the Tandberg 7000 systemCodec V.E. CameraMonitors Remote control Table microphone Tandberg Natural Audio moduleUnpacking InstallationPrecautions Unpacking and Installing the Monitor Rack Unpacking the BaseInstalling the camera InstallingInstalling the monitors Connecting cables Monitor configuration LAN cableSecuring the cables Attaching the back coversSystem configuration MenuIsdn configuration LAN configuration Welcome menu Getting startedSystem start-up Basics Making and ending calls Making a callTIP Selecting / setting default quality bandwidth Selecting / setting default network Correcting keying mistakes Answer a callEnd a call Directory Press D Irectory to bring up the following menuDelete Entry Add New EntryEdit Entry Add MultiSite Entry Add SiteAdjusting volume General useView outgoing video selfview Microphone on/offDo Not Disturb / Sleep Mode Focusing camera Controlling the Main CameraSelecting video sources Moving / zooming cameraVoice Activated Camera Positioning Storing presets PresetsSelecting presets Far end camera control Fecc Main cam Aux Doc cam VcrSending/receiving still images Sending a still imageViewing a still image Receiving a still imageDuo Video Add Duo VideoEnd a Duo Video call MultiSite MCU Establishing MultiSite meetings using Directory MultiSite cascadingAdding an extra site dial out Press C OnnectDisconnecting sites from a conference Adding an extra site dialPC Presenter PC SoftPresenterWeb-interface Text Chat / Closed CaptioningStreaming Advanced use Main menuVGA Resolutions Call qualityAudio VideoAdvanced call quality 4CIFPresentation Mode Duo Video ModePresentations Duo Video QualityDuo Video Number Duo Video / Still Image sourceAuto-display still image Still image filterUtilities AutoanswerFar end camera control Dual MonitorAuto-PIP Welcome MenuContinuous Presence MCU status lineMCU services Quick Menu Request floor Release floorTerminal Names View site #Chair control Audio Settings Audio InputsPage Audio Outputs Echo Control Page Automatic Gain Control AGC Settings Alert Tones & Volume Restore Audio DefaultsDocument Camera Video SettingsCamera Tracking Mode Focus BrightnessWhitebalance Video NameVGA Settings VNC Settings Terminal Settings Network ConfigurationPage ISDN-BRI Settings CoreIsdn BRI This Service has Limited Access on Some Isdn Networks Parallel dial ISDN-PRI Settings Channels automatically Page PRISM1, PRISMII, Wats Leased E1/T1 Settings External network settings 35/RS-366 cable LAN Settings Page Settings Advanced H.323 Settings RsvpNAT IP Settings Snmp Settings Call Settings Access CodeIncoming MCU calls Incoming telephone callsNetwork Profiles EncryptionMax Call Length Dataport configuration Page Language Software OptionsChannel status DiagnosticsSystem info TIP Restore defaults Call statusView current settings Test subsystemPeripheral Equipment InterfacesPage Dual Monitor Document camera Multiple controllable cameras AudioScience microphone TrackerVCR Recording Video Cassette Recorder VCRVCR Playback Telephone Add-On Extra fixed camerasPC applications Additional microphones Appendices Appendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapterAppendix 3 Connecting the system to PRI/T1 Using CSU adapterLoudspeaker volume Appendix 4 Environmental considerationsIris control and lighting BackgroundGuidelines for setting up videoconferencing rooms How to prepare a typical room for videoconferencingAppendix 5 Using the file system Appendix 6 Access Code ABCAppendix 7 Declaration of Conformity Index Tandberg Videoconferencing System Index To use the dataport for PC applications