Tandberg Data 7000 manual Getting started, System start-up, Welcome menu

Page 21

TANDBERG Videoconferencing System	Getting started

Getting started

System start-up

Your system should be in standby mode. When in standby mode, pressing any key or picking up the remote control will wake up the system. An incoming call will also wake up the system.

If the system does not respond, make sure the system is switched on by using the On/Off switch located at the rear of the Codec (see figure below). After a few seconds you should see a ‘Welcome’ menu on the monitor.

If this does not help, verify that your monitor is switched on.

Welcome menu

After a user-definable boot-up logo is shown, the following ‘Welcome’ menu is shown. This screen should provide you with the most important system information. For further system information, select the Quick key ‘System Info’.

21

Image 21

Contents UserManual Plasma Monitors Trademarks and copyright Environmental IssuesOperator Safety Summary Contents Advanced use Peripheral EquipmentAppendices 108 Index 116 TIP IntroductionLAN Menu structureAt a glance the Tandberg 7000 system Tandberg 7000 Videoconferencing SystemV.E. Camera MonitorsCodec Remote control Tandberg Natural Audio module Table microphoneInstallation PrecautionsUnpacking Unpacking the Base Unpacking and Installing the Monitor RackInstalling Installing the monitorsInstalling the camera Connecting cables LAN cable Monitor configurationSecuring the cables Attaching the back coversMenu System configurationIsdn configuration LAN configuration Getting started System start-upWelcome menu Basics Making a call Making and ending callsTIP Selecting / setting default quality bandwidth Selecting / setting default network Answer a call End a callCorrecting keying mistakes Press D Irectory to bring up the following menu DirectoryAdd New Entry Edit EntryDelete Entry Add Site Add MultiSite EntryGeneral use Adjusting volumeView outgoing video selfview Microphone on/offDo Not Disturb / Sleep Mode Controlling the Main Camera Focusing cameraSelecting video sources Moving / zooming cameraVoice Activated Camera Positioning Presets Selecting presetsStoring presets Main cam Aux Doc cam Vcr Far end camera control FeccSending a still image Sending/receiving still imagesViewing a still image Receiving a still imageAdd Duo Video Duo VideoEnd a Duo Video call MultiSite MCU MultiSite cascading Establishing MultiSite meetings using DirectoryPress C Onnect Adding an extra site dial outAdding an extra site dial Disconnecting sites from a conferencePC SoftPresenter PC PresenterText Chat / Closed Captioning Web-interfaceStreaming Main menu Advanced useCall quality VGA ResolutionsAudio Video4CIF Advanced call qualityDuo Video Mode Presentation ModePresentations Duo Video QualityDuo Video / Still Image source Duo Video NumberAuto-display still image Still image filterAutoanswer UtilitiesFar end camera control Dual MonitorWelcome Menu Auto-PIPContinuous Presence MCU status lineMCU services Quick Menu Release floor Request floorTerminal Names View site #Chair control Audio Inputs Audio SettingsPage Audio Outputs Echo Control Page Automatic Gain Control AGC Settings Restore Audio Defaults Alert Tones & VolumeVideo Settings Camera Tracking ModeDocument Camera Brightness FocusWhitebalance Video NameVGA Settings VNC Settings Network Configuration Terminal SettingsPage Core ISDN-BRI SettingsIsdn BRI This Service has Limited Access on Some Isdn Networks Parallel dial ISDN-PRI Settings Channels automatically Page PRISM1, PRISMII, Wats Leased E1/T1 Settings External network settings 35/RS-366 cable LAN Settings Page Settings Rsvp Advanced H.323 SettingsNAT IP Settings Snmp Settings Access Code Call SettingsIncoming MCU calls Incoming telephone callsEncryption Max Call LengthNetwork Profiles Dataport configuration Page Software Options LanguageDiagnostics System infoChannel status TIP Call status Restore defaultsTest subsystem View current settingsInterfaces Peripheral EquipmentPage Dual Monitor Document camera Multiple controllable cameras Tracker AudioScience microphoneVideo Cassette Recorder VCR VCR PlaybackVCR Recording Extra fixed cameras Telephone Add-OnPC applications Additional microphones Appendices Using Telesync TS-256 SW56/ISDN adapter Appendix 2 Connecting the system to the Switched 56 networkUsing CSU adapter Appendix 3 Connecting the system to PRI/T1Appendix 4 Environmental considerations Loudspeaker volumeIris control and lighting BackgroundHow to prepare a typical room for videoconferencing Guidelines for setting up videoconferencing roomsAppendix 5 Using the file system ABC Appendix 6 Access CodeAppendix 7 Declaration of Conformity Index Tandberg Videoconferencing System Index To use the dataport for PC applications