IBM SA41-5155-05 manual This is where you load the new operating system

Page 31

__

4.

For considerations when upgrading an AS/400 or iSeries 400 server with

 

 

OptiConnect installed, see the book OptiConnect for OS/400, SC41-5414-02.

__

5.

For considerations when upgrading an AS/400 or iSeries 400 server with

 

 

Integrated Netfinity® Server installed, see the book Getting Started with

 

 

Integrated Netfinity Server, SC41-5123-01.

__

6.

Refer to “How to Gather Performance Information” on page 8 in order to

 

 

record the performance of your system.

This is where you load the new operating system.

__ 7. See the manual Software Installation, SC41-5120-05 to install software (for example, Licensed Internal Code, operating system, PTFs, etc.). Install software for the required and desired partitions. A PDF version of this manual is available from the iSeries Information Center under System planning and installation -> Hardware and software -> Software and licensed programs -> Install software.

Important: If you are using logical partitions, update all your partitions to V5R1, if needed.

__ 8. Delete any unused device configuration descriptions (delete unused line, line descriptions, and non-reporting resources).

Important: To delete line and device and descriptions, use the WRKLIND and WRKDEVD commands and verify that all the descriptions listed are in use. If you are sure one is not, you should delete it. If you are not sure, you should leave it.

Table 5. Clear non-reporting resources on each LPAR Partition.

No LPAR

LPAR Primary

LPAR Secondary

 

 

 

Use the Hardware Service

Use the Hardware Service

Use the same procedure as

Manager service option to

Manager service option to

described for the LPAR

remove non-reporting

remove non-reporting

Primary for each Secondary

resources that no longer are

resources that no longer are

Partition that is configured.

associated with existing

associated with existing

 

hardware.

hardware.

 

 

Attention: Ensure all I/O

 

 

resources are assigned to a

 

 

partition.

 

 

 

 

__ 9. Before proceeding with the next step, make that sure during step 7, you obtained or performed the following:

a.OS/400 is current (You determined whether you needed to replace software and replaced Licensed Internal Code, operating system, and licensed programs if needed.)

b.PTFs are current

c.Saved your current system (recommended as recovery data in case of disaster)

__ 10. If you do not have a current system backup that allows you to recover in case of disaster, save the entire system on each partition. Make sure that you save the system and data on a tape unit that is compatible with the tape unit on the target system. To save the system, use option 21 on the Save menu. For more information about saving the entire system using option 21, refer to any of the following:

vThe chapter on saving your iSeries server in the manual Backup and Recovery, SC41-5304-05. A PDF version of this manual is available from

Chapter 3. Procedure for an Upgrade (RISC-to-RISC) 19

Page 30 Page 32
Image 31
Page 30 Page 32
Contents ISeries 940x RISC-to-RISC Road Map Page ISeries 940x RISC-to-RISC Road Map Sixth Edition May Contents Iv iSeries 940x RISC-to-RISC Road Map V5R1 Who Should Read This Book ISeries 940x RISC-to-RISC Road Map, SA41-5155-05Conventions and Terminology Used in This Book V4R4M0 Prerequisite and related information Under the System Planning and Installation topicOperations Navigator How to send your commentsISeries 940x RISC-to-RISC Road Map, SA41-5155-05 ISeries 940x RISC-to-RISC Road Map V5R1 What is in this Road Map? Overview of RISC-to-RISC Upgrades and Data MigrationsUpgrade process flow What is an Upgrade?What is a Data Migration? How Long will the Upgrade Take?Hardware Investment for Upgrading Data migration process flow How Long will the Data Migration Take? Books to Use for Software Release UpgradesISeries 940x RISC-to-RISC Road Map V5R1 Planning Your Order for Upgrading or Data Migration Determining Your Upgrade NeedsHow to Gather Performance Information How to Gather Configuration InformationHardware Considerations Prerequisites Before Placing an OrderVersion 4 Software Items Other Software Related ItemsServices and Other Assistance System Configuration ConsiderationsModel-specific Considerations for Placing an Order Upgrading from a 4xx, 5xx, Sxx, or 6xx to a Migrating from a 5xx to an Who is Responsible for Ordering the Upgrade? Placing the Upgrade OrderUpgrading from a 6xx or 7xx to an Sending the Order to a Software Service Provider Other Than How to Get Help with the OrderSending the Order to IBM ISeries 940x RISC-to-RISC Road Map V5R1 Who is Responsible for Upgrading the System Procedure for an Upgrade RISC-to-RISCPreparing the Current System What to Do When the Hardware ArrivesThis is where you load the new operating system Preparing for System Assurance prior to hardware upgrade Print Disk Configuration Status of the installed system ISeries 940x RISC-to-RISC Road Map V5R1 System Assurance Checkpoint Managing your new system I/O resources Installing the Hardware for the RISC-to-RISC UpgradeInformation Center under System planning and installation ISeries 940x RISC-to-RISC Road Map V5R1 Change Description Label display appears Perform a normal IPL Performing a new system backupProcedure for an Upgrade RISC-to-RISC Systems Management Work management- Work Management Manuals Prerequisites for data migration Risc to Risc Procedure for a Data Migration RISC-to-RISCPreparing the source system for the migration Data migration RISC-to-RISC Procedure for a Data Migration RISC-to-RISC ISeries 940x RISC-to-RISC Road Map V5R1 ISeries Planning and Migration Services Appendix A. AS/400 Global ServicesISeries and AS/400 Data Migration Services Lpar Planning and Implementation ServicesPerformance Examinations Related Support ServicesAS/400 Solution Services Installation Services Consulting ServicesMidrange Enhanced Software Service Mress ISeries 940x RISC-to-RISC Road Map V5R1 IBM Http Server for AS/400 Appendix B. Considerations and SolutionsClustering and Logical Partitions SRC A900 2000 RecoveryOperations Console OptiConnect Integrated Netfinity ServerHow to Move Freed Database Files without New Members Command to restore the file. For a logical file, use PTF ISeries 940x RISC-to-RISC Road Map V5R1 Appendix D. Notices IBM TrademarksAppendix D. Notices ISeries 940x RISC-to-RISC Road Map V5R1 Rtvcfgsrc IndexISeries 940x RISC-to-RISC Road Map V5R1 How satisfied are you that the information in this book is Readers’ Comments We’d Like to Hear from YouBusiness Reply Mail Page SA41-5155-05
Top Page Image Contents