Maxtor NVR-2028 manual Wireless Network Structure of the NVR and Its LANCAMs, 192

Page 14

xi.Push the Setup button to save the setup data.

xii.When the words "WAITING" flash on and off at the bottom of the screen, if the screen goes blank, you can press the "Power" button to close the device and press it again to resume its operation.

6.Go to the IP/ACCOUNT option on the LANCAM SETUP page in the NVR setup menu. Choose any channel between 1 to 8 channels to set up the LANCAM IP address. Push the Search button to find all LANCAM IP addresses and push the Enter button to choose one of them to set the channel. Repeat step 6 to set each LANCAM IP address.

NOTE: You need to use an RS-232 cable enclosed in our package and not any other cable, or an error may happen.

NOTE: Once the LANCAM power cord is plugged into the outlet, it will scan the AP or NVR device automatically and obtain an IP address from a DHCP server. This action will continue until a DHCP server is found. If the LANCAM cannot find it after two minutes, its IP address will change to static IP mode as 192. 168. 1. 168. The user can push the DHCP DIP switch on the side of the LANCAM down and up once to reset the static IP to dynamic IP (DHCP client).

NOTE: If the DHCP server of the NVR-2028 is activated, the default NVR IP address is set as

192.168. 1. 205.

3.1.2The Wireless Network Structure of the NVR and Its LANCAMs

The illustration below shows the wireless network of a WIRELESS NVR-2028device connected with its LANCAM client units, whose maximum number is eight.

wireless Lancamwireless Lancam

 

(UP TO 8 WIRELESS LANCAMS CONNECTION)

wireless Lancam

wireless Lancam

 

 

 

 

ANT

Audio in

WAN

LAN

 

 

 

 

 

SD Card

Video in

 

 

 

RS-232

 

 

MONITOR

AUDIO

ALARM I/O

MonitorNVR

DC12V

12

Image 14
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Hard disk compartment lock Front ViewHard-disk drive compartment Left / Right CH1-CH5 /CH2-CH6 buttons Setup/Save buttonRec Indicator Up / Down CH4-CH8 /CH3-CH7 buttonsMobile Rack Power LED Disk IndicatorPower Indicator Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Maxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Search Operations Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search Search Thumbnail Year Full List Alarm List Time Search Channel : Thumbnail SD CardSD Card Search 2003Backup Backup Main EXT Disk SET to Backup Backup OperationsMobile Rack HD Backup Operations Alarm Select Main Backup ALLSearch button Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting Bandwidth0600-1800 0000-0000 REC Schedule Timer Enable on1200-1800 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableRS232 Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup OperationWEP KEY 1 … WEP KEY WEP KEY SET Wireless SET WEP Encryption MechanismKEY Comm SET Lancam Wireless Setting Main SET NetworkTCP Main SET Network StatusPublic Private Protocol Port 2000 205 2001 168Main SET IP Pool Range IP Pool Range Setting Disables itEnables it Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 REC HD Backup Full Main Disk REFORMAT/CLEARHD Backup System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingSet IP Address Configure Your NVR-2028 Network SettingsEnable Dhcp Function System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software Click Start Settings Control Panel Network TCP/IP installationTCP/IP Configuration setting Connection Testing Click Start Programs MS-DOS PromptPage Introduction to Network Viewer Wire WirelessNetwork Viewer PIN no RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN AssignmentView the NVR video from a remote PC Viewing images View the connected device Click to leave the Device Setup windowExit Function Buttons Description Play ListPage Set the Alarm Setup Change the PC System SettingSet the System Setup Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Browsing images from the NVR Connecting the NVRDescription of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Model Number Wireless NVR-2028Design and specifications subject to change without notice Appendix 1. -SCANIP Page Page Communication Protocol SetupGeneral Command Format Value of a specific front panel key Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Statedhcpwait Statesearch Statebackup