Maxtor NVR-2028 manual Command Types, Value of a specific front panel key

Page 90

< The value of a specific front panel key >

KEY_PLAY	1
KEY_STOP	3
KEY_PAUSE	4
KEY_POWER	5
KEY_REC	6
KEY_SETUP	7
KEY_ENTER	8
KEY_SEARCH	10
KEY_DISPLAY	11
KEY_UP	13
KEY_DOWN	14
KEY_LEFT	15
KEY_RIGHT	16
KEY_SHIFT	36
JOG_L	128
JOG_R	129
KEY_SHIFT_LEFT	140
KEY_SHIFT_RIGHT	141
KEY_SHIFT_DOWN	142
KEY_SHIFT_UP	143
KEY_SHIFT_ENTER	144
KEY_SHIFT_DISPLAY	145
KEY_SHIFT_SEARCH	146
KEY_SHIFT_SETUP	147
KEY_SHIFT_POWER	148
KEY_SHIFT_PLAY	149
KEY_SHIFT_PAUSE	150
KEY_SHIFT_REC	151
KEY_SHIFT_STOP	152
KEY_SHUT_L8	160
KEY_SHUT_L7	161
KEY_SHUT_L6	162
KEY_SHUT_L5	163
KEY_SHUT_L4	164
KEY_SHUT_L3	165
KEY_SHUT_L2	166
KEY_SHUT_L1	167
KEY_SHUT_CT	168
KEY_SHUT_R1	169
KEY_SHUT_R2	160
KEY_SHUT_R3	161
KEY_SHUT_R4	162
KEY_SHUT_R5	163
KEY_SHUT_R6	164
KEY_SHUT_R7	165
SIGNAL_POWER	256
SIGNAL_REC_IN	257
SIGNAL_REC_OUT	258

3.Command Types

3.0Command (Main Category=0x02)

3.1Handshake (Second Category=0x01)

PC Request: <0x41>, <0x01>, <0x20>, <0x02>, <0x01>, <0x00>, <0x4f>

NVR Response: <0x41>, <0x20>, <0x01>, <0x02>, <0x08>, <0x00>, <0x4f>

88

Image 90

Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Front View Hard-disk drive compartmentHard disk compartment lock Left / Right CH1-CH5 /CH2-CH6 buttons Setup/Save buttonRec Indicator Up / Down CH4-CH8 /CH3-CH7 buttonsMobile Rack Power LED Disk IndicatorPower Indicator Shuttle RingRear View Alarm In/Out This Figure is Looked from the Rear ViewNo Connection Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Hard-Disk Drive Installation SeagateMaxtor System Information Updating System Software Configuring Recording Settings 352 X Audio OFF720 X Audio OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-00000000-0000 Alarm Recording MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations REC → 〔STOP 〕 →Slow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Search Operations Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Full List SearchTime Search Thumbnail SearchDD MM Year HH MM 24 / 12 / 2003 00 Search Thumbnail Year Full List Alarm List Time Search Channel ： Thumbnail SD CardSD Card Search 2003Backup Backup Main EXT Disk SET to Backup Backup OperationsMobile Rack HD Backup Operations Alarm Select Main Backup ALLSearch button Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting BandwidthREC Schedule Timer Enable on 1200-18000600-1800 0000-0000 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableRS232 Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup OperationWEP KEY SET Wireless SET WEP Encryption Mechanism KEYWEP KEY 1 … WEP KEY Comm SET Lancam Wireless Setting Main SET NetworkTCP Main SET Network StatusPublic Private Protocol Port 2000 205 2001 168Main SET IP Pool Range IP Pool Range Setting Disables itEnables it Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 HD Backup Full Main Disk REFORMAT/CLEAR HD BackupREC System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingSet IP Address Configure Your NVR-2028 Network SettingsEnable Dhcp Function System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software TCP/IP installation TCP/IP Configuration settingClick Start Settings Control Panel Network Connection Testing Click Start Programs MS-DOS PromptPage Wire Wireless Network ViewerIntroduction to Network Viewer PIN no RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN AssignmentView the NVR video from a remote PC Click to leave the Device Setup window ExitViewing images View the connected device Function Buttons Description Play ListPage Change the PC System Setting Set the System SetupSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the regular record settings Set the Alarm record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Connecting the NVR Description of functional keysBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Wireless NVR-2028 Design and specifications subject to change without noticeModel Number Appendix 1. -SCANIP Page Page Setup General Command FormatCommunication Protocol Command Types Command Main Category=0x02 Handshake Second Category=0x01Value of a specific front panel key Statedhcpwait Statesearch Statebackup