Maxtor NVR-2028 manual Slow Forward/Reverse, Play Back Picture-by-picture

Page 27

4.3.2 Slow Forward/Reverse

There are 5 speeds available for a slow playback: 1/2, 1/4, 1/8, 1/16, 1/32.

While playing back recorded video at the recorded speed:

(1)Press the PAUSE button for the slow playback mode.

(2)Forward: Turn the Shuttle dial to the right to view the recorded video in the forward direction at a speed slower than the recorded speed. Each subsequent turn of the shuttle to the right increases the forward rate, as 1/2, 1/4, 1/8, 1/16, and 1/32.

(3)Reverse: Turn the Shuttle dial to the left to view the recorded video in the reverse direction at a speed slower than the recorded speed. Each subsequent turn of the shuttle to the left increases the reverse rate, as -1/2, -1/4, -1/8, -1/16, and -1/32.

(4)Normal: Release the Shuttle dial and then press the PLAY button to return to the normal speed of playback.

4.3.3Play Back Picture-by-picture

While playing back recorded video at the recorded speed:

(1)Press the PAUSE button for the picture-by-picture mode.

(2)There are two ways, by PAUSE button or by JOG, available to play in the picture-by-picture mode, but the PAUSE button can only function in a forward direction; the other, JOG dial , can act in both a forward and a backward direction, as well as picture-by-picture.

By PAUSE button :

Press the PAUSE button to display one frame/field of a picture at a time in the forward direction. (When playing back video recorded by multi channel, each sequential press of the PAUSE button will display each camera in sequence.)

By JOG dial :

Turn the JOG dial clockwise to display one frame/field of a picture at a time in the forward direction. Turn the JOG dial counterclockwise to display one frame/field of a picture at a time in the backward direction.

(3)Press the PLAY button to return to the normal speed of playback.

4.3.4Play Back Recorded Video from a HDD of the mobile rack

To play back a recorded video from a HD2, take the following steps::

(1)Press the Search button to enter the search mode.

(2)Press the ^” and v” buttons, to select a video; press the <” and >” buttons, to flip over a page.

(3)Use the search function to access desired recorded video. For specific operation details please refer to the next section 4.4 (Search Operations).

25

Image 27
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Front View Hard-disk drive compartmentHard disk compartment lock Up / Down CH4-CH8 /CH3-CH7 buttons Setup/Save buttonRec Indicator Left / Right CH1-CH5 /CH2-CH6 buttonsShuttle Ring Disk IndicatorPower Indicator Mobile Rack Power LEDRear View Alarm In/Out This Figure is Looked from the Rear ViewNo Connection Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam192 Wireless Network Structure of the NVR and Its LANCAMsHard-Disk Drive Installation SeagateMaxtor System Information Updating System Software Configuring Recording Settings 352 X Audio OFF720 X Audio OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-00000000-0000 Alarm Recording MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowREC → 〔STOP 〕 → Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReverseSlow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Full List Search Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Search OperationsTime Search Thumbnail SearchDD MM Year HH MM 24 / 12 / 2003 00 2003 Alarm List Time Search Channel : Thumbnail SD CardSD Card Search Search Thumbnail Year Full ListAlarm Select Main Backup ALL Backup OperationsMobile Rack HD Backup Operations Backup Backup Main EXT Disk SET to Backup1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage Search buttonSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameQuality Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Image Setting Quality Highest Medium LOW Lowest SET LancamImage SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC SettingREC Schedule Timer Enable on 1200-18000600-1800 0000-0000 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingOperation Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup RS232WEP KEY SET Wireless SET WEP Encryption Mechanism KEYWEP KEY 1 … WEP KEY Main SET Network Comm SET Lancam Wireless Setting2001 168 Main SET Network StatusPublic Private Protocol Port 2000 205 TCPGateway XXX.YYY.ZZZ.TTT………………..NAT local IP Disables itEnables it Main SET IP Pool Range IP Pool Range SettingRS-232 HD Backup Full Main Disk REFORMAT/CLEAR HD BackupREC On Powers up the device System SettingSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03System Main Goto Comm SET Ethernet Dhcp Configure Your NVR-2028 Network SettingsEnable Dhcp Function Set IP AddressPage TCP/IP Communication Software TCP/IP installation TCP/IP Configuration settingClick Start Settings Control Panel Network Click Start Programs MS-DOS Prompt Connection TestingPage Wire Wireless Network ViewerIntroduction to Network Viewer PIN Assignment RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN noView the NVR video from a remote PC Click to leave the Device Setup window ExitViewing images View the connected device Play List Function Buttons DescriptionPage Change the PC System Setting Set the System SetupSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the regular record settings Set the Alarm record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Connecting the NVR Description of functional keysBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Wireless NVR-2028 Design and specifications subject to change without noticeModel Number Appendix 1. -SCANIP Page Page Setup General Command FormatCommunication Protocol Command Types Command Main Category=0x02 Handshake Second Category=0x01Value of a specific front panel key Statedhcpwait Statesearch Statebackup