Maxtor NVR-2028 manual RJ-45 PIN configuration for Ethernet, PIN no, PIN Assignment, Tx + Rx +

Page 68

RJ-45 PIN configuration for Ethernet

RJ-45 socket

PIN NO.

PIN Assignment

1.

TX +

2.

TX -

3.

RX +

1 2 3 4 5 6 7 8

4.

Not Connected

5.

Not Connected

6.

RX -

7.

Not Connected

8.

Not Connected

Physical specification for Ethernet

Wire Type

Cat. 5

Connector Type

RJ-45

Max. Cable Length

30 m

Hub Wiring Configuration

Straight Through

PC Wiring Configuration

Cross Over

NOTE: If you use the wireless function, you need to know the correct ESSID and WEP KEY of the NVR concerned. Now select the ESSID and enter the WEP KEY of the laptop.

10.1.2 Install the Network Viewer in your PC

Install the Network Viewer from the supported CD-R.

1.Exit all applications currently running in the selected PC.

2.Insert the supported CD in the CD-ROM drive. The program will execute the installation automatically. Follow the on-screen instructions to proceed with the rest of the installation procedure as they appear.

3.After the installation is complete, pop up the START menu from your computer, and point to Programs

/Wireless NVR Network Viewer to open up the program selection page as shown below. Click the Wireless NVR Network Viewer tag to start the Wireless NVR Network Viewer program.

Install the Network Viewer for the ZIP file.

1.Save the ZIP file to your PC and extract the file to a designated directory.

2.Open the extracted folder.

3. Click on the icon to execute the installation and then follow the on-screen instructions as they appear to proceed with the rest of the installation procedure.

4.After the installation is complete, pop up the START menu from your computer, and point to Programs

/Wireless NVR Network Viewer to start the Wireless NVR Network Viewer program.

NOTE: Please make sure the TCP/IP communication software has been properly set and configured in your computer. To check your TCP/IP settings, refer to the following document.

66

Image 68

Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Hard disk compartment lock Front ViewHard-disk drive compartment Setup/Save button Rec IndicatorLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsDisk Indicator Power IndicatorMobile Rack Power LED Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Maxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingOperation Status From REC mode to Playback mode Playback OperationsFast Forward/Reverse REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Alarm list Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search Alarm List Time Search Channel ： Thumbnail SD Card SD Card SearchSearch Thumbnail Year Full List 2003Backup Operations Mobile Rack HD Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLAlarm Select Main Backup Alarm Disk Setting Reformat HD2 UsageSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleQuality Highest Lancam SET Image Resolution Image Setting Resolution Setting CH1 CH2 CH3 CH4Image Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting Bandwidth0600-1800 0000-0000 REC Schedule Timer Enable on1200-1800 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableMain Wireless Setting Wireless Setting Operation SET Privacy Lancam SetupRS232 OperationWEP KEY 1 … WEP KEY WEP KEY SET Wireless SET WEP Encryption MechanismKEY Comm SET Lancam Wireless Setting Main SET NetworkMain SET Network Status Public Private Protocol Port 2000 205TCP 2001 168Disables it Enables itMain SET IP Pool Range IP Pool Range Setting Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 REC HD Backup Full Main Disk REFORMAT/CLEARHD Backup System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConfigure Your NVR-2028 Network Settings Enable Dhcp FunctionSet IP Address System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software Click Start Settings Control Panel Network TCP/IP installationTCP/IP Configuration setting Connection Testing Click Start Programs MS-DOS PromptPage Introduction to Network Viewer Wire WirelessNetwork Viewer RJ-45 PIN configuration for Ethernet Install the Network Viewer for the ZIP filePIN no PIN AssignmentView the NVR video from a remote PC Viewing images View the connected device Click to leave the Device Setup windowExit Function Buttons Description Play ListPage Set the Alarm Setup Change the PC System SettingSet the System Setup Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Browsing images from the NVR Connecting the NVRDescription of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Model Number Wireless NVR-2028Design and specifications subject to change without notice Appendix 1. -SCANIP Page Page Communication Protocol SetupGeneral Command Format Value of a specific front panel key Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Statedhcpwait Statesearch Statebackup