Maxtor NVR-2028 manual Rear View

Page 11

2.2 Rear View
34	35	26	25	27

WAN LAN

MONITOR AUDIO

ANT

SD Card

RS-232

ALARM	I/O	DC12V
		DC12V

28

29

30

31

32 33

ANTENNA: This is one standard wireless access, complies with IEEE 802.11g/b.

SD CARD Slot: This is used for system software updating and archiving/accessing critical images.

RS-232Port: The RS-232 communication port functions as a connector to an external control device. Please refer to APPENDIX 2 for more details.

MONITOR Connector: The connector provides the unit’s composite video live signal if connected to a display device.

AUDIO OUT: This provides the unit’s audio signal to a speaker.

ALARM I/O: This is a 9-PIN D-SUB connector including GROUND, ALARM OUT, DISK FULL, and RECORD IN for connecting with external devices. Please refer to the next section for details.

Wire Catch: The wire catch secures the power cord and keeps it in place (so that it does not droop or hang loosely).

Ground Screw’s: The ground screw is for chassis terminal.

Plug Inlet: The inlet connects to an external power supply. Connect 12 V DC UL Listed Class 2 Power Supply.

WAN PORT: The WAN port is linked with DSL/Cable modem’s cable to the Internet.

LAN PORT: The LAN port connects you to the local network.

9

Image 11

Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Hard disk compartment lock Front ViewHard-disk drive compartment Up / Down CH4-CH8 /CH3-CH7 buttons Setup/Save buttonRec Indicator Left / Right CH1-CH5 /CH2-CH6 buttonsShuttle Ring Disk IndicatorPower Indicator Mobile Rack Power LEDRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam192 Wireless Network Structure of the NVR and Its LANCAMsMaxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowREC → 〔STOP 〕 → Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Full List Search Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Search OperationsDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search 2003 Alarm List Time Search Channel ： Thumbnail SD CardSD Card Search Search Thumbnail Year Full ListAlarm Select Main Backup ALL Backup OperationsMobile Rack HD Backup Operations Backup Backup Main EXT Disk SET to Backup1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage Search buttonSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameQuality Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Image Setting Quality Highest Medium LOW Lowest SET LancamImage SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC Setting0600-1800 0000-0000 REC Schedule Timer Enable on1200-1800 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingOperation Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup RS232WEP KEY 1 … WEP KEY WEP KEY SET Wireless SET WEP Encryption MechanismKEY Main SET Network Comm SET Lancam Wireless Setting2001 168 Main SET Network StatusPublic Private Protocol Port 2000 205 TCPGateway XXX.YYY.ZZZ.TTT………………..NAT local IP Disables itEnables it Main SET IP Pool Range IP Pool Range SettingRS-232 REC HD Backup Full Main Disk REFORMAT/CLEARHD Backup On Powers up the device System SettingSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03System Main Goto Comm SET Ethernet Dhcp Configure Your NVR-2028 Network SettingsEnable Dhcp Function Set IP AddressPage TCP/IP Communication Software Click Start Settings Control Panel Network TCP/IP installationTCP/IP Configuration setting Click Start Programs MS-DOS Prompt Connection TestingPage Introduction to Network Viewer Wire WirelessNetwork Viewer PIN Assignment RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN noView the NVR video from a remote PC Viewing images View the connected device Click to leave the Device Setup windowExit Play List Function Buttons DescriptionPage Set the Alarm Setup Change the PC System SettingSet the System Setup Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Browsing images from the NVR Connecting the NVRDescription of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Model Number Wireless NVR-2028Design and specifications subject to change without notice Appendix 1. -SCANIP Page Page Communication Protocol SetupGeneral Command Format Value of a specific front panel key Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Statedhcpwait Statesearch Statebackup