Maxtor NVR-2028 manual Alarm Recording, 30 SEC

Page 22

4.2.3 Alarm Recording

Take the following steps to activate the programmed alarm recording. For ALM OPERATION, ALM DURATION, MAX REC RATE, and PRE-ALARMsettings, please refer to section 5.4 for more details.

(1)Press the Setup button to enter the MAIN MENU.

(2)Select ALARM and press the Enter button to enter the ALARM SETTING.

(3)Set the desired ALM DURATION and MAX REC RATE for use.

(4)To activate the alarm recording, set ALM OPERATION to ON. To deactivate it, set ALM OPERATION to OFF.

MAIN MENU

LAN CAMERA RECORD / BANDWIDTH CLOCK / TIMER / SEQ ALARM COMMUNICATION DISK

SYSTEM

GOTO ALARM PAGE

ALARM SETTING

ALM OPERATION	: ON
ALM DURATION	: 30 SEC
MAX REC RATE	: UNLIMIT
PRE- ALARM	: OFF

MAIN PAGE

ALARM REC ENABLE

(5)To active the motion alarm recording, Select MOTION SETTING and press the Enter button to enter the MOTION SETTING PAGE, set MOTION ENABLE TO ON, and set a suitable SENSITIVITY and REGION according to the video sources. (Please refer to the next section 4.2.4)

20

Image 22

Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Hard-disk drive compartment Front ViewHard disk compartment lock Left / Right CH1-CH5 /CH2-CH6 buttons Setup/Save buttonRec Indicator Up / Down CH4-CH8 /CH3-CH7 buttonsMobile Rack Power LED Disk IndicatorPower Indicator Shuttle RingRear View This Figure is Looked from the Rear View Alarm In/OutNo Connection Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Seagate Hard-Disk Drive InstallationMaxtor System Information Updating System Software 352 X Audio OFF Configuring Recording Settings720 X Audio OFF Recording Operations Timer RecordingManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 W0000-0000 MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Alarm Recording30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations REC → 〔STOP 〕 →Play Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Search Operations Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Full List SearchThumbnail Search Time SearchDD MM Year HH MM 24 / 12 / 2003 00 Search Thumbnail Year Full List Alarm List Time Search Channel ： Thumbnail SD CardSD Card Search 2003Backup Backup Main EXT Disk SET to Backup Backup OperationsMobile Rack HD Backup Operations Alarm Select Main Backup ALLSearch button Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting Bandwidth1200-1800 REC Schedule Timer Enable on0600-1800 0000-0000 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableRS232 Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup OperationKEY WEP KEY SET Wireless SET WEP Encryption MechanismWEP KEY 1 … WEP KEY Comm SET Lancam Wireless Setting Main SET NetworkTCP Main SET Network StatusPublic Private Protocol Port 2000 205 2001 168Main SET IP Pool Range IP Pool Range Setting Disables itEnables it Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 HD Backup HD Backup Full Main Disk REFORMAT/CLEARREC System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingSet IP Address Configure Your NVR-2028 Network SettingsEnable Dhcp Function System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software TCP/IP Configuration setting TCP/IP installationClick Start Settings Control Panel Network Connection Testing Click Start Programs MS-DOS PromptPage Network Viewer Wire WirelessIntroduction to Network Viewer PIN no RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN AssignmentView the NVR video from a remote PC Exit Click to leave the Device Setup windowViewing images View the connected device Function Buttons Description Play ListPage Set the System Setup Change the PC System SettingSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the Alarm record settings Set the regular record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Description of functional keys Connecting the NVRBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Design and specifications subject to change without notice Wireless NVR-2028Model Number Appendix 1. -SCANIP Page Page General Command Format SetupCommunication Protocol Command Main Category=0x02 Handshake Second Category=0x01 Command TypesValue of a specific front panel key Statedhcpwait Statesearch Statebackup