Maxtor NVR-2028 manual 0000-0000 M 0000-0000 W

Page 21

MAIN MENU

LAN CAMERA

RECORD / BANDWIDTH

CLOCK / TIMER / SEQ

ALARM

COMMUNICATION

DISK

SYSTEM

GOTO CLOCK/TIMER/SEQ PAGE

CLOCK / TIMER / SEQ

CLOCK SETTING		: SET
TIMER		: SET
SEQUENCER		: SET

MAIN PAGE

SET REC SCHEDULE

REC SCHEDULE

TIMER ENABLE: OFF

START END

START END

MAIN MENU

LAN CAMERA

RECORD / BANDWIDTH

CLOCK / TIMER / SEQ

ALARM

COMMUNICATION

DISK

SYSTEM

GOTO CLOCK/TIMER/SEQ PAGE

CLOCK / TIMER / SEQ
CLOCK SETTING		: SET
TIMER		: SET
SEQUENCER		: SET

MAIN PAGE

SET REC SCHEDULE

REC SCHEDULE

TIMER ENABLE: ON

START END

START END

S: 00:00-00:00 M: 00:00-00:00

T: 00:00-00:00 W: 00:00-00:00

T: 00:00-00:00

F: 00:00-00:00

S: 00:00-00:00

OK

TO MOVE

00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00

CANCEL

TO CHANGE

S : 00:00-00:00					00:00-00:00
M: 00:00-00:00					00:00-00:00
T : 00:00-00:00					00:00-00:00
W: 00:00-00:00					00:00-00:00
T : 00:00-00:00					00:00-00:00
F : 00:00-00:00					00:00-00:00
S : 00:00-00:00					00:00-00:00
				OK			CANCEL
				TO MOVE			TO CHANGE

19

Image 21

Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Front View Hard-disk drive compartmentHard disk compartment lock Rec Indicator Setup/Save buttonLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsPower Indicator Disk IndicatorMobile Rack Power LED Shuttle RingRear View Alarm In/Out This Figure is Looked from the Rear ViewNo Connection Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam192 Wireless Network Structure of the NVR and Its LANCAMsHard-Disk Drive Installation SeagateMaxtor System Information Updating System Software Configuring Recording Settings 352 X Audio OFF720 X Audio OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-00000000-0000 Alarm Recording MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowPlayback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse REC → 〔STOP 〕 →Slow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Search Full List Alarm List Time Search Thumbnail SD Card Alarm list SearchSearch Operations Full List SearchTime Search Thumbnail SearchDD MM Year HH MM 24 / 12 / 2003 00 SD Card Search Alarm List Time Search Channel ： Thumbnail SD CardSearch Thumbnail Year Full List 2003Mobile Rack HD Backup Operations Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLDisk Setting Reformat HD2 Usage Alarm Select Main Backup AlarmSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Save to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameResolution Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC SettingREC Schedule Timer Enable on 1200-18000600-1800 0000-0000 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingWireless Setting Operation SET Privacy Lancam Setup Main Wireless SettingRS232 OperationWEP KEY SET Wireless SET WEP Encryption Mechanism KEYWEP KEY 1 … WEP KEY Main SET Network Comm SET Lancam Wireless SettingPublic Private Protocol Port 2000 205 Main SET Network StatusTCP 2001 168Enables it Disables itMain SET IP Pool Range IP Pool Range Setting Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 HD Backup Full Main Disk REFORMAT/CLEAR HD BackupREC On Powers up the device System SettingSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Enable Dhcp Function Configure Your NVR-2028 Network SettingsSet IP Address System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software TCP/IP installation TCP/IP Configuration settingClick Start Settings Control Panel Network Click Start Programs MS-DOS Prompt Connection TestingPage Wire Wireless Network ViewerIntroduction to Network Viewer Install the Network Viewer for the ZIP file RJ-45 PIN configuration for EthernetPIN no PIN AssignmentView the NVR video from a remote PC Click to leave the Device Setup window ExitViewing images View the connected device Play List Function Buttons DescriptionPage Change the PC System Setting Set the System SetupSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the regular record settings Set the Alarm record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Connecting the NVR Description of functional keysBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Wireless NVR-2028 Design and specifications subject to change without noticeModel Number Appendix 1. -SCANIP Page Page Setup General Command FormatCommunication Protocol Command Types Command Main Category=0x02 Handshake Second Category=0x01Value of a specific front panel key Statedhcpwait Statesearch Statebackup