Maxtor NVR-2028 manual Sensitivity Highest Region 30, 25 90

Page 40

MAIN MENU

LAN CAMERA

RECORD / BANDWIDTH

CLOCK / TIMER / SEQ

ALARM

COMMUNICATION

DISK

SYSTEM

LANCAM SETTING

MOTION SETTING

MOTION ENABLE : ON

SENSITIVITY/REGION : CH1

LANCAM PAGE

SET MOTION ENABLE

MOTION SETTING

MOTION ENABLE	: OFF
	ON
		SET

LANCAM PAGE

SET MOTION ENABLE

MOTION ENABLE SETTING

CH1 CH2 CH3 CH4

ON ON ON ON

CH5 CH6 CH7 CH8

ON ON ON ON

OK CANCEL

38

LANCAM SETTING

IP/ACCOUNT	: SET
IMAGE	: SET
AUDIO ENABLE	: OFF
MOTION	: SET
MAIN PAGE
MOTION SETTING

MOTION SETTING

MOTION ENABLE : ON

SENSITIVITY/REGION : CH1

LANCAM PAGE

SET MOTION SENSITIVITY/REGION

MOTION SETTING

MOTION ENABLE SENSITIVITY/REGION : CH1

CH2

CH3

CH4

CH5

CH6

CH7

CH8

LANCAM PAGE

SET MOTION OF CH5

SENSITIVITY / REGION SETTING

SENSITIVITY HIGHEST REGION ( 30, 25 ) – ( 90, 70 )

OK CANCEL

Image 40

Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Hard-disk drive compartment Front ViewHard disk compartment lock Setup/Save button Rec IndicatorLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsDisk Indicator Power IndicatorMobile Rack Power LED Shuttle RingRear View This Figure is Looked from the Rear View Alarm In/OutNo Connection Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Seagate Hard-Disk Drive InstallationMaxtor System Information Updating System Software 352 X Audio OFF Configuring Recording Settings720 X Audio OFF Recording Operations Timer RecordingManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 W0000-0000 MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Alarm Recording30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingOperation Status From REC mode to Playback mode Playback OperationsFast Forward/Reverse REC → 〔STOP 〕 →Play Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Alarm list Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Full List SearchThumbnail Search Time SearchDD MM Year HH MM 24 / 12 / 2003 00 Alarm List Time Search Channel ： Thumbnail SD Card SD Card SearchSearch Thumbnail Year Full List 2003Backup Operations Mobile Rack HD Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLAlarm Select Main Backup Alarm Disk Setting Reformat HD2 UsageSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleQuality Highest Lancam SET Image Resolution Image Setting Resolution Setting CH1 CH2 CH3 CH4Image Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting Bandwidth1200-1800 REC Schedule Timer Enable on0600-1800 0000-0000 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableMain Wireless Setting Wireless Setting Operation SET Privacy Lancam SetupRS232 OperationKEY WEP KEY SET Wireless SET WEP Encryption MechanismWEP KEY 1 … WEP KEY Comm SET Lancam Wireless Setting Main SET NetworkMain SET Network Status Public Private Protocol Port 2000 205TCP 2001 168Disables it Enables itMain SET IP Pool Range IP Pool Range Setting Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 HD Backup HD Backup Full Main Disk REFORMAT/CLEARREC System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConfigure Your NVR-2028 Network Settings Enable Dhcp FunctionSet IP Address System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software TCP/IP Configuration setting TCP/IP installationClick Start Settings Control Panel Network Connection Testing Click Start Programs MS-DOS PromptPage Network Viewer Wire WirelessIntroduction to Network Viewer RJ-45 PIN configuration for Ethernet Install the Network Viewer for the ZIP filePIN no PIN AssignmentView the NVR video from a remote PC Exit Click to leave the Device Setup windowViewing images View the connected device Function Buttons Description Play ListPage Set the System Setup Change the PC System SettingSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the Alarm record settings Set the regular record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Description of functional keys Connecting the NVRBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Design and specifications subject to change without notice Wireless NVR-2028Model Number Appendix 1. -SCANIP Page Page General Command Format SetupCommunication Protocol Command Main Category=0x02 Handshake Second Category=0x01 Command TypesValue of a specific front panel key Statedhcpwait Statesearch Statebackup