Maxtor NVR-2028 manual Front View, Hard-disk drive compartment, Hard disk compartment lock

Page 8

2. DESCRIPTION OF THE FRONT/REAR VIEW

2.1 Front View

1

23

2

24

3

4

5

6

PLAY STOP

PAUSE REC

REV

FWD

 

 

 

 

 

 

 

 

Seq.

 

Power

Display

Setup

Search

 

 

 

Enter

Shift

A-rec

 

Save

 

CH1

CH2

CH3

CH4

4 8

 

T-rec

 

 

 

CH5

CH6

CH7

CH8

 

 

 

DISK

POWER

7

8

9

10

11

14

13

12

15

16

17

18

19

20

21

22

Hard-disk drive compartment:

The compartment allows you to install a hard disk drive mostly for backup purposes. Make sure the drive is well secured with the mounting screws in the mobile rack before you put the rack into the compartment. And remember to turn on the power of the compartment by locking it.

Hard disk compartment lock:

The key lock secures a hard disk in place. Unlock the compartment before you remove the hard disk from the slot without turning off the device.

PAUSE button:

In a playback display, press this to freeze the display. During the freeze, press to display one frame/field of a picture at a time in the forward direction. (Illuminate green in PAUSE mode.) PLAY button:

Press to play back a recorded video from the hard disk. (Illuminate green in PLAY mode.) STOP button:

Press to stop playing back a recorded video or recording video into a hard disk. (Illuminate green in STOP mode.)

REC button:

Push to start recording video into a hard disk while in the live display mode. (Illuminate red in REC mode.)

POWER button:

Press this button for at least 3 seconds to power off. Press again to activate the device. DISPLAY button:

Press to show the system operation status on the screen.

In the LANCAM SETTING mode, use these buttons to display the desired LAN Camera image on the screen.

6

Image 8
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Hard disk compartment lock Front ViewHard-disk drive compartment Setup/Save button Rec IndicatorLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsDisk Indicator Power IndicatorMobile Rack Power LED Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Maxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingOperation Status From REC mode to Playback mode Playback OperationsFast Forward/Reverse REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Alarm list Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search Alarm List Time Search Channel : Thumbnail SD Card SD Card SearchSearch Thumbnail Year Full List 2003Backup Operations Mobile Rack HD Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLAlarm Select Main Backup Alarm Disk Setting Reformat HD2 UsageSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleQuality Highest Lancam SET Image Resolution Image Setting Resolution Setting CH1 CH2 CH3 CH4Image Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting Bandwidth0600-1800 0000-0000 REC Schedule Timer Enable on1200-1800 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableMain Wireless Setting Wireless Setting Operation SET Privacy Lancam SetupRS232 OperationWEP KEY 1 … WEP KEY WEP KEY SET Wireless SET WEP Encryption MechanismKEY Comm SET Lancam Wireless Setting Main SET NetworkMain SET Network Status Public Private Protocol Port 2000 205TCP 2001 168Disables it Enables itMain SET IP Pool Range IP Pool Range Setting Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 REC HD Backup Full Main Disk REFORMAT/CLEARHD Backup System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingConfigure Your NVR-2028 Network Settings Enable Dhcp FunctionSet IP Address System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software Click Start Settings Control Panel Network TCP/IP installationTCP/IP Configuration setting Connection Testing Click Start Programs MS-DOS PromptPage Introduction to Network Viewer Wire WirelessNetwork Viewer RJ-45 PIN configuration for Ethernet Install the Network Viewer for the ZIP filePIN no PIN AssignmentView the NVR video from a remote PC Viewing images View the connected device Click to leave the Device Setup windowExit Function Buttons Description Play ListPage Set the Alarm Setup Change the PC System SettingSet the System Setup Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Browsing images from the NVR Connecting the NVRDescription of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Model Number Wireless NVR-2028Design and specifications subject to change without notice Appendix 1. -SCANIP Page Page Communication Protocol SetupGeneral Command Format Value of a specific front panel key Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Statedhcpwait Statesearch Statebackup