Maxtor NVR-2028 manual Motion

Page 41

MOTION:

Take the steps detailed below to activate a programmed motion detection. For MOTION SETTING, as well as its two distinct functions of MOTION ENABLE and SENSITIVITY / REGION.

(1)Press the Setup button to enter the MAIN MENU.

(2)Select the item termed "LAN CAMERA" and press the Enter button to enter the LANCAM SETTING page.

(3)Select the item termed "MOTION" and push the Enter button to enter the MOTION SETTING page.

(4)To activate the motion detection function, set "MOTION ENABLE" to "ON". To deactivate the function, set "MOTION ENABLE" to " OFF" The items termed "OFF" and "ON" switch all the channels in the MOTION ENABLE SETTING page off and on respectively as well. If you wish to select individual channels for viewing, select the item termed " SET" and activates your desired channels by pressing them "ON" while turning the rest "OFF". Confirm your choices by pressing "OK". If not, push "CANCEL".

(5)In the MOTION SETTING page, select the entry termed "SENSITIVITY / REGION" and press the “>” button to show all the channels in their order, each in turn. Use the “^” button and the “v” button to select a desired channel for setting. Press the Enter button and set the channel in the SENSITIVITY / REGION SETTING page. Repeat the process for all other channels you choose.

(6)To set "SENSITIVITY" and "REGION" for activation on the SENSITIVITY / REGION page, choose your degree of sensitivity and then push the Enter button . At once the legends "OK" and "CANCEL" appear at the bottom of the page. Now press the “<” button and the “>” button to confirm either "OK" or "CANCEL" respectively.

39

Image 41
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Hard disk compartment lock Front ViewHard-disk drive compartment Rec Indicator Setup/Save buttonLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsPower Indicator Disk IndicatorMobile Rack Power LED Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam192 Wireless Network Structure of the NVR and Its LANCAMsMaxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowPlayback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Search Full List Alarm List Time Search Thumbnail SD Card Alarm list SearchSearch Operations Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search SD Card Search Alarm List Time Search Channel : Thumbnail SD CardSearch Thumbnail Year Full List 2003Mobile Rack HD Backup Operations Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLDisk Setting Reformat HD2 Usage Alarm Select Main Backup AlarmSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Save to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameResolution Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC Setting0600-1800 0000-0000 REC Schedule Timer Enable on1200-1800 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingWireless Setting Operation SET Privacy Lancam Setup Main Wireless SettingRS232 OperationWEP KEY 1 … WEP KEY WEP KEY SET Wireless SET WEP Encryption MechanismKEY Main SET Network Comm SET Lancam Wireless SettingPublic Private Protocol Port 2000 205 Main SET Network StatusTCP 2001 168Enables it Disables itMain SET IP Pool Range IP Pool Range Setting Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 REC HD Backup Full Main Disk REFORMAT/CLEARHD Backup On Powers up the device System SettingSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Enable Dhcp Function Configure Your NVR-2028 Network SettingsSet IP Address System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software Click Start Settings Control Panel Network TCP/IP installationTCP/IP Configuration setting Click Start Programs MS-DOS Prompt Connection TestingPage Introduction to Network Viewer Wire WirelessNetwork Viewer Install the Network Viewer for the ZIP file RJ-45 PIN configuration for EthernetPIN no PIN AssignmentView the NVR video from a remote PC Viewing images View the connected device Click to leave the Device Setup windowExit Play List Function Buttons DescriptionPage Set the Alarm Setup Change the PC System SettingSet the System Setup Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Browsing images from the NVR Connecting the NVRDescription of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Model Number Wireless NVR-2028Design and specifications subject to change without notice Appendix 1. -SCANIP Page Page Communication Protocol SetupGeneral Command Format Value of a specific front panel key Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Statedhcpwait Statesearch Statebackup