Maxtor NVR-2028 manual Playback Operations, Fast Forward/Reverse, Rec → 〔Stop 〕 →

Page 26

4.3 Playback Operations

This section shows you how to operate the fast, slow, and single-picture playback functions, and details how the unit is to playback a file in a different operation status. Please refer to the following paragraphs specifying the relevant details. When playing a file, the monitor should display a flashing PLAY message and the PLAY button will light up indicating that the NVR is in the playback status.

Operation Status

A. From REC mode to Playback mode

(In live mode, directly press the PLAY button to play a latest recorded video)

RECSTOP

PLAY……………………………… Play the latest recorded file

 

Play to the end of the file…Show the ending message (use search functions or

 

rewind to replay the file if required)

STOPPLAY…………Play the file from the stop position

B. Search to play back a particular recorded video

SearchPLAY………………………………………… Play a selected file

Play to the end of the file…………Show the ending message (Search again or rewind to

replay the file if required)

STOPPLAY…………………Play the file from the stop position

4.3.1 Fast Forward/Reverse

There are 7 speeds available for playback: 1x, 2x, 4x, 8x, 16x, 32x and 100x

While playing back recorded video at recorded speed:

Forward: Turn the Shuttle dial to the right to view the recorded video in the forward direction at a speed faster than the recorded speed. Each subsequent turn of the shuttle to the right increases the forward rate, as 2x, 4x, 8x, 16x, 32x and 100x.

Reverse: Turn the Shuttle dial to the left to view the recorded video in the reverse direction at a speed faster than the recorded speed. Each subsequent turn of the shuttle to the left increases the reverse rate, as -1x, -2x, -4x, -8x, -16x, -32x and -100x.

Normal: Release the Shuttle dial to return to the normal speed of playback.

24

Image 26
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Hard disk compartment lock Front ViewHard-disk drive compartment Left / Right CH1-CH5 /CH2-CH6 buttons Setup/Save buttonRec Indicator Up / Down CH4-CH8 /CH3-CH7 buttonsMobile Rack Power LED Disk IndicatorPower Indicator Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Maxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Search Operations Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search Search Thumbnail Year Full List Alarm List Time Search Channel : Thumbnail SD CardSD Card Search 2003Backup Backup Main EXT Disk SET to Backup Backup OperationsMobile Rack HD Backup Operations Alarm Select Main Backup ALLSearch button Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting Bandwidth0600-1800 0000-0000 REC Schedule Timer Enable on1200-1800 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableRS232 Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup OperationWEP KEY 1 … WEP KEY WEP KEY SET Wireless SET WEP Encryption MechanismKEY Comm SET Lancam Wireless Setting Main SET NetworkTCP Main SET Network StatusPublic Private Protocol Port 2000 205 2001 168Main SET IP Pool Range IP Pool Range Setting Disables itEnables it Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 REC HD Backup Full Main Disk REFORMAT/CLEARHD Backup System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingSet IP Address Configure Your NVR-2028 Network SettingsEnable Dhcp Function System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software Click Start Settings Control Panel Network TCP/IP installationTCP/IP Configuration setting Connection Testing Click Start Programs MS-DOS PromptPage Introduction to Network Viewer Wire WirelessNetwork Viewer PIN no RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN AssignmentView the NVR video from a remote PC Viewing images View the connected device Click to leave the Device Setup windowExit Function Buttons Description Play ListPage Set the Alarm Setup Change the PC System SettingSet the System Setup Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Browsing images from the NVR Connecting the NVRDescription of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Model Number Wireless NVR-2028Design and specifications subject to change without notice Appendix 1. -SCANIP Page Page Communication Protocol SetupGeneral Command Format Value of a specific front panel key Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Statedhcpwait Statesearch Statebackup