Maxtor NVR-2028 manual REC Schedule Timer Enable on, 1200-1800, 0600-1800 0000-0000

Page 43

5.3 CLOCK / TIMER / SEQ SETTING

The NVR-2028 provides a weekly table, consisting of two periods of time each day for scheduled recording. This option allows you to set the time each day that the NVR will start and stop recording.

MAIN MENU

LAN CAMERA

RECORD / BANDWIDTH

CLOCK / TIMER / SEQ

ALARM

COMMUNICATION

DISK

SYSTEM

GOTO CLOCK / TIMER / SEQ PAGE

CLOCK SETTING:

This entry allows users to set the system time.

CLOCK / TIMER / SEQ

CLOCK SETTING

: SET

TIMER

: SET

SEQUENCER

: SET

MAIN PAGE

SET CURRENT CLOCK

NOTE: Clock data is retained for about 3 months after the 15-hour power supply is used up (Operate On mode).

TIMER:

This entry allows users to program the time each day that the NVR will start and stop recording. There are two time periods each day available for scheduling. The time is displayed in a 24-hour clock format. If there is a time overlapping showing between two continual time period settings, the device will automatically combine the two time-period settings into one combined time-period setting.

TIMER ENABLE: This option enables/disables the programmed scheduled recording. ON: Enables the scheduled recording.

OFF: Disables the scheduled recording.

REC SCHEDULE

TIMER ENABLE: ON

START END

START END

S 06:00-16:00

12:00-18:00

REC SCHEDULE

TIMER ENABLE: ON

START END

START END

S 06:00-18:00

00:00-00:00

 

 

 

 

SEQUENCER:

To regulate dwell time of the sequencer, you can use the “^” button and the “v” button to select dwell time provided here, ranging from the "00" to the "30".you can set individual channels in different dwell time. After set individual channels, quad and multi screen in different modes and then push the Enter button . At once the legends "OK" and "CANCEL" appear at the bottom of the page. Now press the “<” button and the “>” button to confirm either "OK" or "CANCEL" respectively. Press "OK" to ratify your choice(s). If not, press "CANCEL".

41

Image 43
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Hard-disk drive compartment Front ViewHard disk compartment lock Up / Down CH4-CH8 /CH3-CH7 buttons Setup/Save buttonRec Indicator Left / Right CH1-CH5 /CH2-CH6 buttonsShuttle Ring Disk IndicatorPower Indicator Mobile Rack Power LEDRear View This Figure is Looked from the Rear View Alarm In/OutNo Connection Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam192 Wireless Network Structure of the NVR and Its LANCAMsSeagate Hard-Disk Drive InstallationMaxtor System Information Updating System Software 352 X Audio OFF Configuring Recording Settings720 X Audio OFF Recording Operations Timer RecordingManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 W0000-0000 MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Alarm Recording30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowREC → 〔STOP 〕 → Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReversePlay Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Full List Search Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Search OperationsThumbnail Search Time SearchDD MM Year HH MM 24 / 12 / 2003 00 2003 Alarm List Time Search Channel : Thumbnail SD CardSD Card Search Search Thumbnail Year Full ListAlarm Select Main Backup ALL Backup OperationsMobile Rack HD Backup Operations Backup Backup Main EXT Disk SET to Backup1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage Search buttonSave to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameQuality Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Image Setting Quality Highest Medium LOW Lowest SET LancamImage SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC Setting1200-1800 REC Schedule Timer Enable on0600-1800 0000-0000 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingOperation Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup RS232KEY WEP KEY SET Wireless SET WEP Encryption MechanismWEP KEY 1 … WEP KEY Main SET Network Comm SET Lancam Wireless Setting2001 168 Main SET Network StatusPublic Private Protocol Port 2000 205 TCPGateway XXX.YYY.ZZZ.TTT………………..NAT local IP Disables itEnables it Main SET IP Pool Range IP Pool Range SettingRS-232 HD Backup HD Backup Full Main Disk REFORMAT/CLEARREC On Powers up the device System SettingSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03System Main Goto Comm SET Ethernet Dhcp Configure Your NVR-2028 Network SettingsEnable Dhcp Function Set IP AddressPage TCP/IP Communication Software TCP/IP Configuration setting TCP/IP installationClick Start Settings Control Panel Network Click Start Programs MS-DOS Prompt Connection TestingPage Network Viewer Wire WirelessIntroduction to Network Viewer PIN Assignment RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN noView the NVR video from a remote PC Exit Click to leave the Device Setup windowViewing images View the connected device Play List Function Buttons DescriptionPage Set the System Setup Change the PC System SettingSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the Alarm record settings Set the regular record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Description of functional keys Connecting the NVRBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Design and specifications subject to change without notice Wireless NVR-2028Model Number Appendix 1. -SCANIP Page Page General Command Format SetupCommunication Protocol Command Main Category=0x02 Handshake Second Category=0x01 Command TypesValue of a specific front panel key Statedhcpwait Statesearch Statebackup