Maxtor NVR-2028 manual SD Card Search, Search Thumbnail Year Full List, 2003

Page 30

(5)There are 5 levels of recording range modes to choose from: 1 Hour, 10 Minutes, 1 Minute, 10 Seconds and 1 Second. Select the specific field of your requirement and press the Enter button to enter the next level. If you want to return the previous level, please press the Setup button

(6)Once reaching the critical point at any level, the user can start playback by just clicking the PLAY button .

SEARCH

 

 

THUMBNAIL

 

 

DD

MM

YEAR

 

FULL LIST

 

 

 

 

 

 

 

/ 12 /

2003

 

 

22

 

ALARM LIST

 

 

 

 

 

 

 

TIME SEARCH

 

 

CHANNEL1

 

THUMBNAIL

 

 

 

 

 

 

 

 

 

 

 

 

SD CARD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.4.5 SD CARD Search

Take the following steps to proceed with the SD card search function.

(1)Insert a SD Card into the SD card slot of the rear unit.

(2)Press the Search button to enter the search mode.

(3)Select the SD CARD and press the Enter button to access the complete list of JPG files.

(4)Highlight the specific JPG file of your requirement and press the Enter button to display the image.

(5)If you need another, please return to the SD card JPG file list page and repeat steps (3) and (4) again for another search.

SEARCH

FULL LIST

ALARM LIST TIME SEARCH THUMBNAIL SD CARD

SD CARD JPG FILE

F0000.JPG

F0001.JPG

F0002.JPG

F0003.JPG

F0004.JPG

F0005.JPG

NOTE: If you would like to delete JPG file in the SD card, please return to SD CARD JPG FILE list page and highlight the specific JPG file of your requirement and press the Setup button and then select the “Yes” to delete the image.

28

Image 30
Contents Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Features Product IntroductionPage Front View Hard-disk drive compartmentHard disk compartment lock Left / Right CH1-CH5 /CH2-CH6 buttons Setup/Save buttonRec Indicator Up / Down CH4-CH8 /CH3-CH7 buttonsMobile Rack Power LED Disk IndicatorPower Indicator Shuttle RingRear View Alarm In/Out This Figure is Looked from the Rear ViewNo Connection Use a RS-232 cable to install a wireless setting in a Lancam Basic ConnectionWireless Network Structure of the NVR and Its LANCAMs 192Hard-Disk Drive Installation SeagateMaxtor System Information Updating System Software Configuring Recording Settings 352 X Audio OFF720 X Audio OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-00000000-0000 Alarm Recording MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingFast Forward/Reverse Operation Status From REC mode to Playback modePlayback Operations REC → 〔STOP 〕 →Slow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Search Operations Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Full List SearchTime Search Thumbnail SearchDD MM Year HH MM 24 / 12 / 2003 00 Search Thumbnail Year Full List Alarm List Time Search Channel : Thumbnail SD CardSD Card Search 2003Backup Backup Main EXT Disk SET to Backup Backup OperationsMobile Rack HD Backup Operations Alarm Select Main Backup ALLSearch button Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to F0000.JPG Save to F0001.JPG Save to F000N.JPGKey Lock Operation Menu Setup Login Name TitleImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion REC Setting BandwidthREC Schedule Timer Enable on 1200-18000600-1800 0000-0000 Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableRS232 Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup OperationWEP KEY SET Wireless SET WEP Encryption Mechanism KEYWEP KEY 1 … WEP KEY Comm SET Lancam Wireless Setting Main SET NetworkTCP Main SET Network StatusPublic Private Protocol Port 2000 205 2001 168Main SET IP Pool Range IP Pool Range Setting Disables itEnables it Gateway XXX.YYY.ZZZ.TTT………………..NAT local IPRS-232 HD Backup Full Main Disk REFORMAT/CLEAR HD BackupREC System Setting On Powers up the deviceSituation MAC 00 0c 0c 00 00 Bios Date Dec 24 Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingSet IP Address Configure Your NVR-2028 Network SettingsEnable Dhcp Function System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software TCP/IP installation TCP/IP Configuration settingClick Start Settings Control Panel Network Connection Testing Click Start Programs MS-DOS PromptPage Wire Wireless Network ViewerIntroduction to Network Viewer PIN no RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN AssignmentView the NVR video from a remote PC Click to leave the Device Setup window ExitViewing images View the connected device Function Buttons Description Play ListPage Change the PC System Setting Set the System SetupSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the regular record settings Set the Alarm record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Connecting the NVR Description of functional keysBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Wireless NVR-2028 Design and specifications subject to change without noticeModel Number Appendix 1. -SCANIP Page Page Setup General Command FormatCommunication Protocol Command Types Command Main Category=0x02 Handshake Second Category=0x01Value of a specific front panel key Statedhcpwait Statesearch Statebackup