RIDGID microEXPLORER manual Controls

Page 11

microEXPLORERDigital Inspection Camera

8.Prepare the camera for inspection. The camera cable may need to be pre-formed or bent to properly inspect the area. Do not try to form bends less than 2" radius. This can damage cable. If inspecting a dark space, turn the LEDs on before in- serting the camera or cable.

Do not use excessive force to insert or withdraw the cable. This may result in damage to the electrical device or in- spection area. Do not use the cable or imager head to modify surroundings, clear pathways or clogged areas, or as anything other than an inspection de- vice. This may result in damage to the electrical device or inspection area. Do not insert the camera or cable into any space that will require less than a 2" bend radius. Tight bends could damage the cable.

9.When the inspection is complete, care- fully withdraw the camera and cable from the inspection area.

10.Remove the batteries and refer servicing to qualified service personnel under any of the following conditions.

If liquid has been spilled or objects have fallen into product.

If product does not operate normally by following the operating instructions.

If the product has been dropped or dam- aged in any way.

When the product exhibits a distinct change in performance.

Controls

Back – Pressing the back button at any time will take you to the last viewed screen.

Shutter – Pressing shut- ter button will take a still image or start and stop the video recorder.

Figure 10 – Controls

Trash – Pressing the trash button while in the playback screen will delete an image or video.

Select – Pressing select while in live screen will take you to the primary settings screen.

Arrows – Use the arrow buttons to navigate through menus, operate LEDs, zoom and pan.

Ridge Tool Company

9

Image 11
Contents MicroEXPLORER Table of Contents MicroEXPLORER Electrical Safety Safety SymbolsGeneral Safety Information Work Area SafetyMicroEXPLORER Digital Inspection Camera Safety Specific Safety InformationPersonal Safety ServiceStandard Equipment Description Specifications Standard EquipmentSpecifications DescriptionFCC Statement Tool AssemblyTo Remove or Install the Battery Pack Lift and pull to remove cap when re- leased. FigureButtons, Controls and Ports Installing the Imager Head CableTo install an SD Card To Install Camera AccessoriesCheck work area for Adequate lighting Tool InspectionTool and Work Area Set-Up See sections on Controls, Icons and On Screen Navigation Operating InstructionsControls ControlsIcons On Screen Navigation Capturing a still image Change From Still Image Capture to VideoTurn Up-Is-Up Self Leveling On or Off PanTransferring Images To a Computer Entering the Secondary Settings ScreenClick OK or next. The following screen will be displayed Following screen will be displayedManually Saving Images to Your Computer’s Hard Drive Cleaning InstructionsMagnet AccessoriesStorage Service and Repair 30083 Imager Head 30203Battery Charge Safety TroubleshootingBattery and Charger Battery Pack/Battery Charger SafetyCooling No Fan Battery & Charger SpecificationsAdequate lighting Charging Procedure/ Operating InstructionsIf present, remove battery from charger Disposal Li-Ion Battery Charger Accessories Catalog Description30208 Charger DC Adapter 30198 74V Li-Ion Battery Pack StorageCaméra d’inspection numérique Table des matières Installation et retrait du bloc-pilesSécurité électrique Symboles de sécuritéConsignes générales de sécurité Sécurité du chantierUtilisation et entretien des appareils électriques Consignes de sécurité spécifiquesSécurité individuelle RévisionsAutonomie Sécurité de la caméra d’inspection numérique microEXPLORERCaractéristiques techniques ApplicationAvertissement FCC Équipements de baseMontage du câble de tête de caméra Retrait et installation du bloc- pilesAssemblage de l’appareil Inspection de l’appareil Montage des accessoires de caméraTouches, commandes et ports Installation de carte mémoireExaminez les lieux pour Un éclairage suffisant Préparation de l’appareil et du chantier11. Éteignez la caméra Utilisation de l’appareil Icônes CommandesIcônes suite Navigation de l’écran Lecture et effacement des images sauvegardées BalayageSaisie d’une photo Saisie d’une vidéo« Menu » , puis appuyez sur la touche de sélection Transfert des images vers un ordinateurAccès à l’écran de programmation secondaire Fenêtre de copie de photos Ouvrez le fichier 100SNAKE Ouvrez le fichier DcimStockage AccessoiresService après-vente et réparations Consignes de nettoyageSécurité du chargeur DépannagePiles et chargeur Sécurité du bloc-piles et du chargeurCourant Caractéristiques techniques du chargeurUn éclairage suffisant Inspection et prépara- tion du chargeurAdaptateur CC pour chargeur Bloc-piles lithium/ion de 3,74 Méthode de chargement et consignes d’utilisationRecyclage Caméra d’inspection numérique microEXPLORER Cámara digital de inspección Información de seguridad general ÍndiceSeguridad eléctrica Simbología de seguridadInformación de seguridad general Seguridad en la zona de trabajoServicio Información de seguridad específicaSeguridad personal Uso y cuidado del aparato eléctricoEspecificaciones Descripción, especifica- ciones y equipo estándarSeguridad de la cámara digital de inspección microEXPLORER DescripciónComunicado de la FCC Ensamblaje del aparatoEquipo estándar Levante y extraiga la tapa. Figura Cómo sacar o instalar el bloque de pilasInstalación del cable del formador de imágenes Instalación de los accesorios de la cámaraBotones de control, mandos y puertos Inspección del aparatoInstalación de la tarjeta de memoria SD Revise que la zona de trabajo Esté bien iluminada Preparación del aparato y de la zona de trabajoApague la cámara Lea la sección Botones de control, man- dos y puertos Instrucciones de funcionamientoAparato ControlesÍconos Indicador de pila completamente cargadaÍconos Navegación en pantalla Revisar y eliminar imágenes guardadas Autonivelación vertical de la imagenToma de una imagen fija Toma de un videoIngreso a la pantalla de posiciones secundarias Transferencia de imá- genes a un computadorFigura 22 Cuadro donde seleccionar imágenes Abra la carpeta 100SNAKE Haga clic en Removable Storage De- viceAbra la carpeta Dcim Servicio y reparaciones AccesoriosInstrucciones de limpieza AlmacenajeSeguridad del cargador de la pila Detección de averíasCargador de pilas Seguridad del bloque de pilas y del cargadorSeguridad de la pila Descripción, especificaciones y equipo estándarEspecificaciones de la pila y del cargador Figura 32 Etiqueta en el cargador Inspección y preparación del cargadorAlmacenamiento Instrucciones deLimpieza Instrucciones de carga y funcionamientoEliminación de las pilas Cámara digital de inspección microEXPLORER E R S O N . C O N S I D E R I T S O L V E D

microEXPLORER specifications

The RIDGID microEXPLORER is a state-of-the-art inspection camera designed to provide users with a convenient and efficient way to visually inspect hard-to-reach areas. This cutting-edge tool leverages advanced imaging technology to deliver high-quality video and photos, making it an indispensable asset for professionals in plumbing, HVAC, electrical, and other maintenance fields.

One of the key features of the microEXPLORER is its 2.4-inch color LCD screen, which offers a bright, clear display for real-time viewing of inspection areas. The screen is designed to provide crisp images, ensuring that users can see details that may not be visible to the naked eye. The camera can capture and save images and video in both JPEG and AVI formats, allowing for easy documentation and sharing of findings with clients or team members.

The RIDGID microEXPLORER incorporates a 17mm camera head that is both compact and versatile. This design allows the camera to navigate tight spaces and various pipe sizes, making it ideal for plumbing inspections and HVAC applications. The camera head features an adjustable LED lighting system, ensuring that the inspection area is well-lit regardless of the surrounding lighting conditions. This functionality is crucial for obtaining clear images in dark or cramped spaces.

Equipped with a 3-foot flexible cable, the microEXPLORER can easily bend and maneuver through tight bends and curves, providing access to otherwise inaccessible areas. The cable's rigidity allows for precise positioning, enabling users to capture detailed footage from unique angles. The device's ergonomic design ensures that handling and operation are comfortable, reducing fatigue during extended use.

Another noteworthy aspect of the RIDGID microEXPLORER is its battery life. The device is powered by a rechargeable lithium-ion battery, offering significant usage time on a single charge. This long-lasting power source allows professionals to complete inspections without the interruption of frequent recharging.

In summary, the RIDGID microEXPLORER is a versatile inspection camera that combines portability, advanced imaging technology, and user-friendly features. Its compact design, high-resolution display, adjustable lighting, and flexible cable make it an essential tool for a variety of inspection tasks. Whether used for diagnosing plumbing issues, inspecting HVAC systems, or evaluating electrical components, the microEXPLORER enhances efficiency and accuracy in fieldwork, making it a valuable tool for professionals across multiple industries.