JVC GR-DVL9600 Insert Editing, Find Edit OUT Point, Find Edit in Point, Pause During Editing

Page 65

Display

6w

TC 12 : 34 : 15

PLA

Y

O

F

F

5S

Lock Button

Power Switch

EN65

Insert Editing

You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in- and out-points. The original audio remains unchanged.

NOTES:

Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape.

To perform Insert Editing while watching in the television, make connections (pg. 48).

1 FIND EDIT OUT POINT

Playback the tape to locate the point where you want to stop editing. Confirm the time code at this point (pg. 47).

2 FIND EDIT IN POINT

Press REW (2) until the point is located, then press PAUSE (6).

Remote sensor

T W START/STOP

DISPLAY INSERT

REW(IND) PAUSE

3 PREPARE FOR INSERT EDITING Press and hold INSERT (w) on the remote control, then press PAUSE (6). “6w” and the Time Code (min.:sec.) appear and the camcorder enters Insert- Pause mode.

4 START RECORDING

Press START/STOP to begin editing.

•Confirm the insert at the time code you checked in step 1.

5 PAUSE DURING EDITING

Press START/STOP. The camcorder re-enters Insert Pause mode. Press again to resume editing.

6 STOP EDITING

Press STOP (5) while the camcorder is in the Insert- Pause mode.

NOTES:

Program AE with special effects (pg. 34) can be used

to spice up the scenes being edited during Insert Editing.

To display the Time Code during Insert Editing,

pg. 46.

STOP

PLAY

When performing Insert Editing, the tape’s Video Area

and Sub-Code Area (pg. 4) are rewritten, so the date

RM-V711U (provided)

and time information changes.

If you perform Insert Editing onto a blank space on the

tape, the audio and video may be disrupted. Make sure

you only edit recorded areas.

During Insert Editing, when the tape moves to scenes

recorded in the LP mode or a blank portion, Insert Edting

stops and “ERROR! REFER MANUAL” appears.

Image 65
Contents GR-DVL9600 It is recommended that you Dear CustomerThis unit is produced to comply with Standard IEC Publ EN3Remote Control Unit RM-V711U Video Cable DC Cord AC Power AdapterCleaning Cloth Charger AA-V68EA Min DVM-30Signal Compression Luminance Signal Y Lens Colour Difference Signal R-Y/B-YAbout DV Analysis Mic ConversionCharging the Battery Pack PowerUsing AC Power Using the Battery PackTilt Viewfinder Upward Attach Battery Pack To Detach The Battery PackGetting Started Date/Time SettingsBattery Open Cassette Cover Loading/Unloading a CassetteINSERT/REMOVE Tape Close Cassette CoverSET Recording Mode Recording Mode Setting10 EN Set depending on your preferenceViewfinder Adjustment Grip AdjustmentTripod Mounting 12 ENShoulder Strap Attachment Operation Mode Recording Basic Recording 14 ENLoad a Cassette Start ShootingPress IND. ON/OFF Button LCD Monitor/Viewfinder IndicationsStop Recording Before the following steps, perform pg 16 ENShooting While Watching The LCD Monitor Brightness Control Journalistic ShootingInterface Shooting Basic Recording 18 ENZoom Zoom OutAfter playing back the recorded tape, when you shoot again When blank portion is recorded on a tapeProper recording ShootingDisplaying The Date And Time During Recording Recording Advanced Features20 EN END 5S Mode Engage 5S ModeSet the Power Switch to the , , or OFF position Dissolves during 5 second recording modeStart Progressive Mode Recording Progressive Mode Recording22 EN To End Progressive Video RecordingRegular shooting of moving images Description of Progressive Scan CCDFrame Scan a Scan B Scan C24 EN Advanced FeaturesRecording Pro SnapshotProgressive Mode Motor Drive ModePin-Up mode √ Multi-Analyser To Remove The Shutter Sound26 EN If the Power Switch is set toSnapshot Flash Auto Flash Engage RECORD-STANDBYPress the Select Dial Flash Brightness AdjustmentAccess Flash Adjustment 28 EN Using Menu For Detailed AdjustmentRecording Menu Explanations Factory-presetSystem Menu Explanations 30 ENDate/Time Menu Explanations Effect Selection Fade/Wipe EffectsFADE/WIPE Selection Select EffectPicture Wipe or Dissolve Selection 32 ENBefore the following steps, perform steps 1 through 4 on pg If you select Picture Wipe/Dissolve during recordingMenu Fader And Wipe MenuDisable Mode Select ModeManual Mode Item Menu AE/EFFECT Menu 34 ENClassic Film ShutterTwilight Sepia36 EN FocusingAuto Focus Patterns that are regularly repeatedEND Adjustment of Focus Access Manual FocusManual Focus To nearer subjectAccess Exposure Control Access Manual Mode Item Menu38 EN Exposure ControlCenter SUBJECT, Lock Iris Iris LockIris To Return To Automatic Iris ControlAccessment White Balance Adjust White Balance Adjustment40 EN To Return To Automatic White BalanceExit Manual White Balance Adjustment Enter SettingManual White Balance Operation To Change The Tint For RecordingHigh Speed Recording 42 ENEngage High Speed Recording Standby END RecordingPlayback Basic Playback Adjust VolumeRewind or Fast-forward the tape Play BackBasic Playback EN PlaybackEND Playback Progressive Slow-Motion PlaybackFind Scene of Interest Playback 46 ENPlayback Menu Close MenuRecording sound Display Output sound Playback SoundDisplaying The Time Code During Playback 48 EN When connecting the cables, open this coverBasic Connections Use the provided S-Video cable and Audio/Video cableTurn on the camcorder, the VCR and the TV Connectinput VCR Output to TV Supply PowerConnectvcr Camcorder to TV or 50 EN Turn on PowerPlayback Advanced Connections Connection To a Personal ComputerConnect Printer to PC if Necessary Connection To a Video Unit Equipped With a DV ConnectorTape Dubbing 52 ENMake Connections Digital DubbingStart Playback Press Play 4 to play back the source tapePull OUT Battery Holder Installing The BatteryInsert Battery in Holder 54ENInfrared beam transmitting window Switch set to the camera positionFunctions Buttons 56 EN Using the Remote Control UnitEffect Play 4 ButtonSelect Menu Remote sensor Random Assemble Editing R.A.Edit 58 ENSET REMOTE/VCR Code SET Remote to Operate VCRSelect Scenes Make ConnectionsSelect Scenes EN Using the Remote Control UnitSET EDIT-IN Point SET EDIT-OUT PointPrepare Source Tape Automatic Editing to VCRStop Editing RM-V711U Provided T WDiagnosing VCR’S Against Camcorder Timing 62 ENFor More Accurate Editing Access Playback Menu Adjustment of VCR’S Against Camcorder TimingPower Switch Playback Menu Input Correction DataAudio Dubbing 64 ENBegin Dubbing Pause During DubbingFind Edit OUT Point Insert EditingFind Edit in Point Pause During EditingCorrective Action 66 ENCorrective Action Symptom Possible Causes68 EN TroubleshootingDuring recording, the date EN Troubleshooting Remove After Use72EN Tally Lamp Power Lamp # Date/Time Reset Button ResetRed-Eye Reduction Button Control VOLIndex 74 ENIndications LCD Monitor/Viewfinder Indications During RecordingIndications Function LCD Monitor/Viewfinder Indications During Playback76 EN For safety, do not To prolong service lifeAvoid using the unit To avoid hazardTo protect the unit, do not Do not leave the unitAbout moisture condensation Serious malfunctioningConnectors AC Power Adapter/Charger AA-V68EACamcorder GeneralGR-DVL9600