Sony BRC-Z330 Connecting a VTR Equipped with, HD-SDI Input Connectors Generator

Page 55

Connecting a VTR Equipped with	Connecting a Sync Signal
HD-SDI Input Connectors	Generator
Attach the optional BRBK-HD2 HD-SDI Output Card	To connect a single camera
to the camera, and turn on the camera. You can output	To connect a single camera
the signal from the camera by converting it into a signal
compliant with HD-SDI standards (SMPTE292M serial
digital interface).

1 2 3 4 5 6 7 8 9 IR SELECT

R

1OFF ON

2DATA MIX

	VISCA RS-422			OFF	ON EXT SYNC IN
!				75
!
DC IN 12V	IN VISCA	RS-232C OUT	S VIDEO	VIDEO	RGB/COMPONENT

	DC IN 12V
	SDI OUTPUT	BRBK-HD2 HD-SDI
	SDI OUTPUT	Output Card
		Output Card

Connecting cable with BNC connectors

to HD-SDI input

HDCAM, etc. equipped with an

HD-SDI input connectors

				75-ohm
1 2 3 4 5 6 7 8 9 IR SELECT	R			termination switch:
1		OFF	ON	ON
2		DATA MIX		ON
3
VISCA RS-422		OFF	ON

! 75

DC IN 12V

IN VISCA

RS-232C OUT

S VIDEO

VIDEO

DC IN 12V

EXT SYNC IN

75-ohm coaxial cable

to SYNC OUT

Sync signal generator

Installation and Connections

Connections

55

Image 55

Contents HD Color Video Camera For the customers in Europe, Australia and New Zealand Owner’s RecordFor the customers in the U.S.A For the customers in CanadaTable of Contents Appendix Precautions Flicker White flecksAliasing Focal planeFeatures Ceiling bracket a Ceiling bracket B Wire rope Supplied Components and AccessoriesCamera MPA-AC1 AC power adaptor Sony AC power cord Remote commanderOptional Products BRS-200 Remote Camera Operating SwitcherBRBK-HD2 HD-SDI Output Card System configuration System ConfigurationThis system allows you Overview System Configuration BRBK-HD2 Rear Location and Function of PartsCamera FrontBottom Setting of the Bottom switchesRemote Commander supplied Mode button RM-BR300 Remote Control Unit not suppliedInstalling batteries Lock button and indicatorWhen the menu of the camera is displayed When the menu of the camera is not displayedTALLY/CONTACT connector Mode selectorVisca RS-232C connector Visca RS-422 connectorBRBK-HD2 HD-SDI Output Card not supplied Wk ON/OFF switchAbout On-Screen Menus Setting MenusMain Menu To return to the normal display Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the main menu4,5 EX-COMP exposure compensation Mode exposure modeFor the 1080/59.94i or 720/59.94P signal format Exposure MenuColor Menu White Balance white balance modeTo set the Color AE To set the Color Detail Picture MenuAF Assist auto focus assist Black and white modeMode focus mode Focus MenuZoom digital zoom Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP PAN Tilt Zoom MenuSystem Menu IR-RECEIVE infrared signal receptionIMG-FLIP image flip Display Info information display Video OUT MenuStatus Menu To turn on/off the camera using the Remote Commander Turning on the PowerIf you accidentally move the camera with your hand Pan/Tilt and Zoom OperationPanning and Tilting To face the camera back to the frontZooming Adjusting the CameraOperating Multiple Cameras with the Remote Commander Focusing on a SubjectShooting with Back Lighting Storing the Camera Settings in MemoryTo cancel the preset memory To recall the stored settingsOperating Multiple Cameras Operation Using the RM-BR300 Remote Control UnitTo assign camera addresses manually To assign camera addresses automaticallyTo set a limit on the maximum panning/ tilting speed Joystick Movement Setting Camera Mode ONE Push AWB Shift VALUE/R Back Light One-push auto focusing during manual focus adjustmentTo adjust the white balance manually Adjusting the White BalanceAdjusting the Brightness To adjust the white balance automaticallyTo store camera settings Storing Camera SettingsTo select positions 9 to Setting the Speed of the Camera Moving to a Preset Position Attaching an Output Card InstallationInstalling the Camera To install the camera on a deskBefore installation Installing the Camera in a High PositionTo attach the camera to a tripod Installation on a ceiling example Wire rope supplied 3M4 To remove the camera Installation on a shelf, etc. in a high position exampleWire rope supplied Installation and Connections To remove the camera Connecting the RM-BR300 Remote Control Unit Connecting to an AC OutletConnections Visca RS-422 Connecting a Device Equipped with Visca RS-422 Connector Connecting a Device Equipped with Visca RS-232C ConnectorVisca RS-422 HD-SDI Input Connectors Generator Connecting a VTR Equipped withTo connect a single camera You can connect up to seven cameras To connect multiple cameras to the HD sync signal generatorList of Messages Indicators on the BRC-Z330 cameraMessages for the BRC-Z330 camera Symptom Cause Remedy TroubleshootingAppendix Troubleshooting Full Auto Menu ConfigurationNormal YP BP R Color Gain Color HUE Color Matrix Enhance General presetting items Presetting ItemsPresetting menu items Setup not available for 1080/50i output signal System SpecificationsInput/output connectors Supplied accessoriesAlways verify that the unit is operating properly before use Top Side Front DimensionsBRC-Z330 Video Camera Ceiling Bracket BRM-BR300 Remote Control Unit Top Pin Assignments Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-232C OUT connector mini DIN 8-pin, femaleVisca RS-232C output connector mini DIN 8- pin, female RM-BR300 Remote Control Unit optionalSecond BRC-Z330 Wiring Diagram of Visca RS-422 ConnectionRM-BR300 Remote Control Unit Third to Seventh BRC-Z330To remove the connector plug Using the Visca RS-422 Connector Plug