Sony BRC-Z330 operating instructions Remote Commander supplied

Page 15

Notes

•Set the switches before you turn on the power of the camera.

•You cannot use a camera with its camera address set to “0” together with cameras with their camera address set to “1” to “7.”

Remote Commander (supplied)

 

 

 

POWER

 

 

 

 

 

6

1

CAMERA SELECT

 

1

2

3

 

 

FOCUS

 

 

2

AUTO

 

MANUAL

 

FAR

NEAR

 

3

DATA SCREEN

 

BACK LIGHT

7

 

 

 

 

 

STD

REV

 

 

 

1

2

3

 

 

4

5

6

8

 

PRESET

 

RESET

 

 

POSITION

 

 

 

PAN-TILT

 

 

4

HOME

 

 

 

 

 

PAN-TILT

 

 

 

 

RESET

9

 

SLOW ZOOM FAST

 

 

 

T

 

T

q;

 

W

W

 

 

 

L/R

5

DIRECTION SET

RM-EV100

ACAMERA SELECT buttons

Press the button corresponding to the camera you want to operate with the Remote Commander. The camera number can be set using the IR SELECT switch on the rear of the camera.

Note

If two or more cameras are adjacent and have the same camera number, they are operated simultaneously with the same Remote Commander. When you install the cameras close to each other, set different camera numbers.

For the camera number setting, see “Operating Multiple Cameras with the Remote Commander” on page 33.

BFOCUS buttons

Used for focus adjustment.

Press the AUTO button to adjust the focus automatically. To adjust the focus manually, press

the MANUAL button, and adjust it with the FAR and NEAR buttons.

CDATA SCREEN button

Press this button to display the main menu. Press it again to turn off the menu. If you press the button when a lower-level menu is selected, the display returns to the next menu one level higher.

Note

Pan/tilt and zoom operations are disabled when the menu is displayed.

DPAN-TILT buttons

Press the arrow buttons to perform panning and tilting. Press the HOME button to face the camera back to the front.

When the menu is displayed, use V or v to select the menu items and B or b to change the set values.

EL/R DIRECTION SET button

Hold down this button and press the REV button to change the direction of the camera movement opposite to that indicated by the arrow of the B/b buttons.

To reset the direction of the camera movement, press the STD button while holding down this button.

FPOWER switch

Press this button to turn on/off the camera when the camera is connected to an AC outlet.

GBACK LIGHT button

Press this button to enable the backlight compensation. Press it again to disable the backlight compensation.

HPOSITION buttons

Hold down the PRESET button and press button 1 to 6 to store the current camera direction, zooming, focus adjustment and backlight compensation in the memory of the pressed number button.

To erase the memory contents, hold down the RESET button and press button 1 to 6.

IPAN-TILT RESET button

Press this button to reset the pan/tilt position.

JZOOM buttons

Use the SLOW button to zoom slowly, and the FAST button to zoom quickly.

Press the T (telephoto) side of the button to zoom in, and the W (wide angle) side to zoom out.

Overview

Location and Function of Parts

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents HD Color Video Camera For the customers in Europe, Australia and New Zealand Owner’s RecordFor the customers in the U.S.A For the customers in CanadaTable of Contents Appendix Precautions Flicker White flecksAliasing Focal planeFeatures Ceiling bracket a Ceiling bracket B Wire rope Supplied Components and AccessoriesCamera MPA-AC1 AC power adaptor Sony AC power cord Remote commanderBRS-200 Remote Camera Operating Switcher Optional ProductsBRBK-HD2 HD-SDI Output Card System Configuration System configurationThis system allows you Overview System Configuration BRBK-HD2 Rear Location and Function of PartsCamera FrontBottom Setting of the Bottom switchesRemote Commander supplied Mode button RM-BR300 Remote Control Unit not suppliedInstalling batteries Lock button and indicatorWhen the menu of the camera is displayed When the menu of the camera is not displayedTALLY/CONTACT connector Mode selectorVisca RS-232C connector Visca RS-422 connectorBRBK-HD2 HD-SDI Output Card not supplied Wk ON/OFF switchSetting Menus About On-Screen MenusMain Menu To return to the normal display Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the main menu4,5 EX-COMP exposure compensation Mode exposure modeFor the 1080/59.94i or 720/59.94P signal format Exposure MenuWhite Balance white balance mode Color MenuTo set the Color AE To set the Color Detail Picture MenuAF Assist auto focus assist Black and white modeMode focus mode Focus MenuZoom digital zoom Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP PAN Tilt Zoom MenuIR-RECEIVE infrared signal reception System MenuIMG-FLIP image flip Display Info information display Video OUT MenuStatus Menu To turn on/off the camera using the Remote Commander Turning on the PowerIf you accidentally move the camera with your hand Pan/Tilt and Zoom OperationPanning and Tilting To face the camera back to the frontZooming Adjusting the CameraOperating Multiple Cameras with the Remote Commander Focusing on a SubjectShooting with Back Lighting Storing the Camera Settings in MemoryTo cancel the preset memory To recall the stored settingsOperating Multiple Cameras Operation Using the RM-BR300 Remote Control UnitTo assign camera addresses automatically To assign camera addresses manuallyTo set a limit on the maximum panning/ tilting speed Joystick Movement Setting Camera Mode ONE Push AWB Shift VALUE/R Back Light One-push auto focusing during manual focus adjustmentTo adjust the white balance manually Adjusting the White BalanceAdjusting the Brightness To adjust the white balance automaticallyStoring Camera Settings To store camera settingsTo select positions 9 to Setting the Speed of the Camera Moving to a Preset Position Attaching an Output Card InstallationInstalling the Camera To install the camera on a deskInstalling the Camera in a High Position Before installationTo attach the camera to a tripod Installation on a ceiling example Wire rope supplied 3M4 To remove the camera Installation on a shelf, etc. in a high position exampleWire rope supplied Installation and Connections To remove the camera Connecting to an AC Outlet Connecting the RM-BR300 Remote Control UnitConnections Visca RS-422 Connecting a Device Equipped with Visca RS-422 Connector Connecting a Device Equipped with Visca RS-232C ConnectorVisca RS-422 Connecting a VTR Equipped with HD-SDI Input Connectors GeneratorTo connect a single camera You can connect up to seven cameras To connect multiple cameras to the HD sync signal generatorIndicators on the BRC-Z330 camera List of MessagesMessages for the BRC-Z330 camera Symptom Cause Remedy TroubleshootingAppendix Troubleshooting Full Auto Menu ConfigurationNormal YP BP R Color Gain Color HUE Color Matrix Enhance Presetting Items General presetting itemsPresetting menu items Setup not available for 1080/50i output signal System SpecificationsInput/output connectors Supplied accessoriesAlways verify that the unit is operating properly before use Top Side Front DimensionsBRC-Z330 Video Camera Ceiling Bracket BRM-BR300 Remote Control Unit Top Pin Assignments Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Visca RS-232C OUT connector mini DIN 8-pin, femaleVisca RS-232C output connector mini DIN 8- pin, female RM-BR300 Remote Control Unit optionalSecond BRC-Z330 Wiring Diagram of Visca RS-422 ConnectionRM-BR300 Remote Control Unit Third to Seventh BRC-Z330To remove the connector plug Using the Visca RS-422 Connector Plug

BRC-Z330 specifications

The Sony BRC-Z330 is a sophisticated PTZ (pan-tilt-zoom) camera that has gained popularity in various applications, including broadcasting, event production, and corporate video conferencing. One of its most striking features is its ability to deliver high-quality images through a 1/2.8-type Exmor CMOS sensor. This sensor allows the BRC-Z330 to capture stunning Full HD 1080p video at 60 frames per second, making it suitable for fast-paced environments.

The camera features a 30x optical zoom lens, which is complemented by a 12x digital zoom, providing users with the ability to focus on details from a considerable distance. With a focal length range of 4.5mm to 135mm, it is versatile enough to work in various shooting scenarios, whether it be capturing wide shots of a conference room or zooming in on a speaker at an event.

In terms of connectivity, the BRC-Z330 offers multiple output options, including HDMI, 3G-SDI, and composite video outputs. This flexibility allows for seamless integration into different broadcasting and recording setups. Additionally, the camera supports IP streaming, enabling remote access and control over a network, which is invaluable for multi-camera setups and remote production tasks.

The BRC-Z330 employs advanced image processing technologies, such as Sony's Dynamic Contrast Enhancement and XDNR (eXtended Dynamic Noise Reduction). These features work to optimize image quality in various lighting conditions, ensuring crisp and clear visuals even in challenging environments.

For ease of operation, the BRC-Z330 is equipped with a user-friendly interface and can be remotely controlled via RS-232 or RS-422 protocols. This functionality is ideal for situations where the camera needs to be adjusted without physical intervention, such as live-streaming events or remote interviews.

Another significant characteristic of the camera is its compact and discreet design, allowing it to blend into various settings without being obtrusive. With its impressive specifications and technological capabilities, the Sony BRC-Z330 has become an essential tool for professionals seeking high-quality video solutions in the ever-evolving world of media production. Its reliability, versatility, and excellent image quality make it a worthy investment for any organization focused on producing top-tier content.
Top Page Image Contents