Sony BRC-Z330 Camera buttons, Mode selector, Visca RS-232C connector, Visca RS-422 connector

Page 18

Overview

Blue: The power of the camera is on.

Yellow green: The camera is in standby mode.

Off: No camera is connected.

Hold down this button and press CAMERA button 1 to 7 to turn on/off the power of the camera corresponding to the pressed button.

SCAMERA buttons

Press one of the buttons to select the camera from among those connected. The selected CAMERA button lights in blue.

TPOSITION buttons

You can store the various camera settings such as the pan, tilt and zoom positions to the memory of the camera corresponding to each POSITION button, and load the settings in the memory.

Rear/Bottom

 

 

 

 

 

MODE RS-232C

VISCA

RS-422

TALLY/CONTACT

CONTACT(TALLY) ! ON/OFF

 

 

 

 

 

TALLY

 

1

9

1

9

CONTACT DC IN 12V

 

 

 

 

 

wa ws wd

 

wf wgwh wj wk

UMODE selector

Select the position corresponding to the VISCA- controllable camera to be connected.

Switch position

Camera mode

0

Automatically selected (default)

 

 

1

BRC-300/300P

 

 

2

EVI-D70/D70P

 

 

3

EVI-D100/D100P

 

 

4

EVI-D30/D30P

 

 

5

SNC-RZ30N

 

 

6

BRC-H700

 

 

7

BRC-Z700

 

 

8

BRC-Z330

 

 

Note

Set the selector to position 8 when all the connected cameras are BRC-Z330s. For other connections, set the selector to position 0.

VVISCA RS-232C connector

Connect to the VISCA RS-232C IN connector of the camera.

WVISCA RS-422 connector

Connect to the VISCA RS-422 connector of the camera.

An RS-422 connector plug is attached at the factory.

XTALLY/CONTACT connector

This connector is used for the tally lamp input or the contact output.

Select the function of the connector using the TALLY/CONTACT selector.

An RS-422 connector plug is attached at the factory.

YTALLY/CONTACT selector

Select the function of the TALLY/CONTACT connector.

TALLY: The tally lamp of the camera selected with the connected switcher lights.

CONTACT: The contact output corresponding to the camera address selected with the Remote Control Unit is short-circuited against the connected switcher.

CONTACT (TALLY): The contact output corresponding to the camera address selected with the Remote Control Unit is short-circuited against the connected switcher and the tally lamp of the camera selected with the Remote Control Unit lights.

Notes

•Change the setting of the selector before you turn on the power for the Remote Control Unit. Otherwise, the setting is not effective.

•For more details on the functions of the TALLY/ CONTACT selector, refer to the Operating Instructions of the RM-BR300.

wh DC IN 12V connector

Connect the supplied AC power adaptor.

wj DIP switches (bottom)

Switch 1 (RS-232C/RS-422 selector)

Set to ON for RS-422, or OFF for RS-232C.

Switch 2 (Communication baud rate selector)

Set to ON for 38400bps, or OFF for 9600bps.

Switch 3 (BRIGHT control function selector)

Set to ON for IRIS and GAIN adjustments, or OFF for IRIS adjustment only.

Note

Set the DIP switches before you turn on the power of the Remote Control Unit. Otherwise, the setting is not effective.

18

Location and Function of Parts

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HD Color Video Camera For the customers in Canada Owner’s RecordFor the customers in the U.S.A For the customers in Europe, Australia and New ZealandTable of Contents Appendix Precautions Focal plane White flecksAliasing FlickerFeatures Remote commander Supplied Components and AccessoriesCamera MPA-AC1 AC power adaptor Sony AC power cord Ceiling bracket a Ceiling bracket B Wire ropeBRS-200 Remote Camera Operating Switcher Optional ProductsBRBK-HD2 HD-SDI Output Card System Configuration System configurationThis system allows you Overview System Configuration BRBK-HD2 Front Location and Function of PartsCamera RearSetting of the Bottom switches BottomRemote Commander supplied Lock button and indicator RM-BR300 Remote Control Unit not suppliedInstalling batteries Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedVisca RS-422 connector Mode selectorVisca RS-232C connector TALLY/CONTACT connectorWk ON/OFF switch BRBK-HD2 HD-SDI Output Card not suppliedSetting Menus About On-Screen MenusMain Menu To return to the main menu Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the normal display4,5 Exposure Menu Mode exposure modeFor the 1080/59.94i or 720/59.94P signal format EX-COMP exposure compensationWhite Balance white balance mode Color MenuTo set the Color AE Picture Menu To set the Color DetailFocus Menu Black and white modeMode focus mode AF Assist auto focus assistPAN Tilt Zoom Menu Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP Zoom digital zoomIR-RECEIVE infrared signal reception System MenuIMG-FLIP image flip Video OUT Menu Display Info information displayStatus Menu Turning on the Power To turn on/off the camera using the Remote CommanderTo face the camera back to the front Pan/Tilt and Zoom OperationPanning and Tilting If you accidentally move the camera with your handFocusing on a Subject Adjusting the CameraOperating Multiple Cameras with the Remote Commander ZoomingStoring the Camera Settings in Memory Shooting with Back LightingTo recall the stored settings To cancel the preset memoryOperation Using the RM-BR300 Remote Control Unit Operating Multiple CamerasTo assign camera addresses automatically To assign camera addresses manuallyTo set a limit on the maximum panning/ tilting speed Joystick Movement Setting Camera One-push auto focusing during manual focus adjustment Mode ONE Push AWB Shift VALUE/R Back LightTo adjust the white balance automatically Adjusting the White BalanceAdjusting the Brightness To adjust the white balance manuallyStoring Camera Settings To store camera settingsTo select positions 9 to Setting the Speed of the Camera Moving to a Preset Position To install the camera on a desk InstallationInstalling the Camera Attaching an Output CardInstalling the Camera in a High Position Before installationTo attach the camera to a tripod Installation on a ceiling example Wire rope supplied 3M4 Installation on a shelf, etc. in a high position example To remove the cameraWire rope supplied Installation and Connections To remove the camera Connecting to an AC Outlet Connecting the RM-BR300 Remote Control UnitConnections Visca RS-422 Connecting a Device Equipped with Visca RS-232C Connector Connecting a Device Equipped with Visca RS-422 ConnectorVisca RS-422 Connecting a VTR Equipped with HD-SDI Input Connectors GeneratorTo connect a single camera To connect multiple cameras to the HD sync signal generator You can connect up to seven camerasIndicators on the BRC-Z330 camera List of MessagesMessages for the BRC-Z330 camera Troubleshooting Symptom Cause RemedyAppendix Troubleshooting Menu Configuration Full AutoNormal YP BP R Color Gain Color HUE Color Matrix Enhance Presetting Items General presetting itemsPresetting menu items Setup not available for 1080/50i output signal Supplied accessories SpecificationsInput/output connectors SystemAlways verify that the unit is operating properly before use Ceiling Bracket B DimensionsBRC-Z330 Video Camera Top Side FrontRM-BR300 Remote Control Unit Top Visca RS-232C OUT connector mini DIN 8-pin, female Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional Visca RS-232C output connector mini DIN 8- pin, femaleThird to Seventh BRC-Z330 Wiring Diagram of Visca RS-422 ConnectionRM-BR300 Remote Control Unit Second BRC-Z330Using the Visca RS-422 Connector Plug To remove the connector plug

BRC-Z330 specifications

The Sony BRC-Z330 is a sophisticated PTZ (pan-tilt-zoom) camera that has gained popularity in various applications, including broadcasting, event production, and corporate video conferencing. One of its most striking features is its ability to deliver high-quality images through a 1/2.8-type Exmor CMOS sensor. This sensor allows the BRC-Z330 to capture stunning Full HD 1080p video at 60 frames per second, making it suitable for fast-paced environments.

The camera features a 30x optical zoom lens, which is complemented by a 12x digital zoom, providing users with the ability to focus on details from a considerable distance. With a focal length range of 4.5mm to 135mm, it is versatile enough to work in various shooting scenarios, whether it be capturing wide shots of a conference room or zooming in on a speaker at an event.

In terms of connectivity, the BRC-Z330 offers multiple output options, including HDMI, 3G-SDI, and composite video outputs. This flexibility allows for seamless integration into different broadcasting and recording setups. Additionally, the camera supports IP streaming, enabling remote access and control over a network, which is invaluable for multi-camera setups and remote production tasks.

The BRC-Z330 employs advanced image processing technologies, such as Sony's Dynamic Contrast Enhancement and XDNR (eXtended Dynamic Noise Reduction). These features work to optimize image quality in various lighting conditions, ensuring crisp and clear visuals even in challenging environments.

For ease of operation, the BRC-Z330 is equipped with a user-friendly interface and can be remotely controlled via RS-232 or RS-422 protocols. This functionality is ideal for situations where the camera needs to be adjusted without physical intervention, such as live-streaming events or remote interviews.

Another significant characteristic of the camera is its compact and discreet design, allowing it to blend into various settings without being obtrusive. With its impressive specifications and technological capabilities, the Sony BRC-Z330 has become an essential tool for professionals seeking high-quality video solutions in the ever-evolving world of media production. Its reliability, versatility, and excellent image quality make it a worthy investment for any organization focused on producing top-tier content.
Top Page Image Contents