Sony BRC-Z330 operating instructions Joystick Movement Setting Camera

Page 38

Operation Using the RM-BR300 Remote Control Unit

CAMERA button Maximum panning/tilting

speed

6

43.4 degrees/sec.

7

60 degrees/sec.

 

 

Only the CAMERA button you pressed flashes, and the corresponding maximum panning/tilting speed is set.

Note

The maximum panning/tilting speed setting is stored in the memory of the optional RM-BR300 Remote Control Unit. If you use another RM-BR300 Remote Control Unit or you connect another camera to the RM-BR300, set a limit on the maximum panning/tilting speed again.

To face the camera back to the front

Press the button on the top of the joystick for one or two seconds.

Press for 1 or 2 seconds.

If you accidentally move the camera with your hand

Press the PAN-TILT RESET button to perform the pan/ tilt reset action.

If the camera moves in a different direction from that you intended

The camera is preset to face toward the right whenever the joystick is inclined to the right. You might wish to face the camera toward the opposite direction from that in which you inclined the joystick, for example, when you change the direction of the camera while checking the picture on the screen. In such a case, press the POSITION 2 (REV) button while holding down the L/R DIRECTION button.

To reset the setting, press the POSITION 1 (STD) button while holding down the L/R DIRECTION button.

Joystick

Movement of the

Setting

 

camera

 

Incline to the right.

 

While holding down

 

 

 

 

L/R

 

 

DIRECTION

 

 

1

 

 

9

 

 

STD

 

 

Press.

Incline to the right.

 

While holding down

 

 

 

 

L/R

 

 

DIRECTION

 

 

2

 

 

10

 

 

REV

 

 

Press.

Note

The setting above only changes the signal emitted from the RM-BR300 Remote Control Unit, and does not change the setting of the camera itself.

If the STANDBY lamp of the camera flashes

When the camera is moved or turned by hand or by external shock, the microcomputer inside the camera may not be able to memorize the pan/tilt position properly and the camera may stop.

To reset the pan/tilt position, press the PAN-TILT RESET button or turn the power of the camera off and turn it on again.

STANDBY flashes.

38

Pan/Tilt and Zoom Operation

Page 37 Page 39
Image 38
Page 37 Page 39
Contents HD Color Video Camera For the customers in Canada Owner’s RecordFor the customers in the U.S.A For the customers in Europe, Australia and New ZealandTable of Contents Appendix Precautions Focal plane White flecksAliasing FlickerFeatures Remote commander Supplied Components and AccessoriesCamera MPA-AC1 AC power adaptor Sony AC power cord Ceiling bracket a Ceiling bracket B Wire ropeBRBK-HD2 HD-SDI Output Card BRS-200 Remote Camera Operating SwitcherOptional Products This system allows you System ConfigurationSystem configuration Overview System Configuration BRBK-HD2 Front Location and Function of PartsCamera RearSetting of the Bottom switches BottomRemote Commander supplied Lock button and indicator RM-BR300 Remote Control Unit not suppliedInstalling batteries Mode buttonWhen the menu of the camera is not displayed When the menu of the camera is displayedVisca RS-422 connector Mode selectorVisca RS-232C connector TALLY/CONTACT connectorWk ON/OFF switch BRBK-HD2 HD-SDI Output Card not suppliedMain Menu Setting MenusAbout On-Screen Menus To return to the main menu Menu Operation Using the Supplied Remote CommanderOperation Through Menus To return to the normal display4,5 Exposure Menu Mode exposure modeFor the 1080/59.94i or 720/59.94P signal format EX-COMP exposure compensationTo set the Color AE White Balance white balance modeColor Menu Picture Menu To set the Color DetailFocus Menu Black and white modeMode focus mode AF Assist auto focus assistPAN Tilt Zoom Menu Setting range of PAN LEFT/PAN RightSetting range of Tilt DOWN/TILT UP Zoom digital zoomIMG-FLIP image flip IR-RECEIVE infrared signal receptionSystem Menu Video OUT Menu Display Info information displayStatus Menu Turning on the Power To turn on/off the camera using the Remote CommanderTo face the camera back to the front Pan/Tilt and Zoom OperationPanning and Tilting If you accidentally move the camera with your handFocusing on a Subject Adjusting the CameraOperating Multiple Cameras with the Remote Commander ZoomingStoring the Camera Settings in Memory Shooting with Back LightingTo recall the stored settings To cancel the preset memoryOperation Using the RM-BR300 Remote Control Unit Operating Multiple CamerasTo set a limit on the maximum panning/ tilting speed To assign camera addresses automaticallyTo assign camera addresses manually Joystick Movement Setting Camera One-push auto focusing during manual focus adjustment Mode ONE Push AWB Shift VALUE/R Back LightTo adjust the white balance automatically Adjusting the White BalanceAdjusting the Brightness To adjust the white balance manuallyTo select positions 9 to Storing Camera SettingsTo store camera settings Setting the Speed of the Camera Moving to a Preset Position To install the camera on a desk InstallationInstalling the Camera Attaching an Output CardTo attach the camera to a tripod Installing the Camera in a High PositionBefore installation Installation on a ceiling example Wire rope supplied 3M4 Installation on a shelf, etc. in a high position example To remove the cameraWire rope supplied Installation and Connections To remove the camera Connections Connecting to an AC OutletConnecting the RM-BR300 Remote Control Unit Visca RS-422 Connecting a Device Equipped with Visca RS-232C Connector Connecting a Device Equipped with Visca RS-422 ConnectorVisca RS-422 To connect a single camera Connecting a VTR Equipped withHD-SDI Input Connectors Generator To connect multiple cameras to the HD sync signal generator You can connect up to seven camerasMessages for the BRC-Z330 camera Indicators on the BRC-Z330 cameraList of Messages Troubleshooting Symptom Cause RemedyAppendix Troubleshooting Menu Configuration Full AutoNormal YP BP R Color Gain Color HUE Color Matrix Enhance Presetting menu items Presetting ItemsGeneral presetting items Setup not available for 1080/50i output signal Supplied accessories SpecificationsInput/output connectors SystemAlways verify that the unit is operating properly before use Ceiling Bracket B DimensionsBRC-Z330 Video Camera Top Side FrontRM-BR300 Remote Control Unit Top Visca RS-232C OUT connector mini DIN 8-pin, female Visca RS-422 connector connector plug 9-pinVisca RS-232C in connector mini-DIN 8-pin, female Pin AssignmentsRM-BR300 Remote Control Unit optional Visca RS-232C output connector mini DIN 8- pin, femaleThird to Seventh BRC-Z330 Wiring Diagram of Visca RS-422 ConnectionRM-BR300 Remote Control Unit Second BRC-Z330Using the Visca RS-422 Connector Plug To remove the connector plug

BRC-Z330 specifications

The Sony BRC-Z330 is a sophisticated PTZ (pan-tilt-zoom) camera that has gained popularity in various applications, including broadcasting, event production, and corporate video conferencing. One of its most striking features is its ability to deliver high-quality images through a 1/2.8-type Exmor CMOS sensor. This sensor allows the BRC-Z330 to capture stunning Full HD 1080p video at 60 frames per second, making it suitable for fast-paced environments.

The camera features a 30x optical zoom lens, which is complemented by a 12x digital zoom, providing users with the ability to focus on details from a considerable distance. With a focal length range of 4.5mm to 135mm, it is versatile enough to work in various shooting scenarios, whether it be capturing wide shots of a conference room or zooming in on a speaker at an event.

In terms of connectivity, the BRC-Z330 offers multiple output options, including HDMI, 3G-SDI, and composite video outputs. This flexibility allows for seamless integration into different broadcasting and recording setups. Additionally, the camera supports IP streaming, enabling remote access and control over a network, which is invaluable for multi-camera setups and remote production tasks.

The BRC-Z330 employs advanced image processing technologies, such as Sony's Dynamic Contrast Enhancement and XDNR (eXtended Dynamic Noise Reduction). These features work to optimize image quality in various lighting conditions, ensuring crisp and clear visuals even in challenging environments.

For ease of operation, the BRC-Z330 is equipped with a user-friendly interface and can be remotely controlled via RS-232 or RS-422 protocols. This functionality is ideal for situations where the camera needs to be adjusted without physical intervention, such as live-streaming events or remote interviews.

Another significant characteristic of the camera is its compact and discreet design, allowing it to blend into various settings without being obtrusive. With its impressive specifications and technological capabilities, the Sony BRC-Z330 has become an essential tool for professionals seeking high-quality video solutions in the ever-evolving world of media production. Its reliability, versatility, and excellent image quality make it a worthy investment for any organization focused on producing top-tier content.
Top Page Image Contents