Operation Using the RM-BR300 Remote Control Unit
Before operating, check that the camera, the
For details, see “Installation” (page 43) and “Connections” (page 51).
Turning on the Power
Operation | 1 |
|
|
|
| LIGHT |
| LIGHT RESET |
| AWB |
| MENU |
|
| 2 RESET |
| PANEL LIGHT | ||||||||
| VALUE | LOCK |
|
| PANEL |
| BLACK |
|
| |||
Using | – | + |
| L/R |
|
|
|
|
|
|
|
|
|
|
|
| RESET |
|
|
|
|
|
|
|
|
| – | + |
|
|
|
|
|
|
|
|
|
|
|
| R |
| PRESET |
|
|
| POSITION |
|
|
|
|
| BRIGHT | MODE |
|
|
|
|
|
|
|
|
| |
|
|
|
| SHIFT | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
|
|
| 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
|
|
|
|
| STD | REV |
|
|
|
|
|
|
the |
| B |
| DIRECTION |
|
|
| CAMERA |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| AUTO |
|
|
|
|
|
|
|
|
|
| FOCUS | AUTO | POWER | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
| |
RM- |
|
| MANUAL |
| ||||||||
|
| ONE PUSH |
|
|
|
|
|
|
|
|
| |
BR300Remote | NEAR | FAR | AF |
|
|
|
|
|
|
|
|
|
| POWER |
|
| CAMERA |
| |||||||
|
|
|
|
| ||||||||
Control | 1 Connect the camera to an AC outlet using the | |||||||||||
The power is turned on and the POWER lamp | ||||||||||||
| supplied AC power adaptor and power cord. | |||||||||||
Unit | lights. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The camera will automatically pan and tilt and be reset to the position stored in POSITION 1 (Pan/tilt reset action).
2 Press the ON/OFF switch on the
The CAMERA button representing the camera whose power was turned off last lights. (The CAMERA 1 button lights by default.)
3 Turn on the peripheral devices.
Note
Be sure to turn on the power for the camera before the power for the Remote Control Unit. Otherwise, the
Remote Control Unit may not recognize the connected camera.
To turn on/off the camera using the RM- BR300 Remote Control Unit
As long as the camera is connected to an AC outlet, you can turn the camera on or off with the POWER button on the Remote Control Unit.
While holding down the POWER button, press the CAMERA button corresponding to the camera whose power you want to turn on/off.
When you turn the power off using the Remote Control Unit, the POWER lamp turns off and the STANDBY lamp lights on the camera.
STANDBY lights.
Note
When you turn off the camera using the Remote Commander, the camera tilts downward to protect the lens from dust before entering Standby mode. When
To illuminate the panel of the Remote Control Unit
Press the PANEL LIGHT button. All the POSITION buttons and CAMERA buttons light.
To turn off the illumination, press the PANEL LIGHT button again.
PANEL
LIGHT
Operating Multiple Cameras
Before operating, you must assign the camera addresses to the connected cameras as follows. Then you can switch the camera to be controlled simply by pressing the corresponding CAMERA button.
36
Turning on the Power