Classe Audio SSP-800/CT-SSP Digital Audio Output Coaxial, Digital Audio Output Optical

Page 20

20

8Digital Audio Output - Coaxial

The SSP supports one digital audio coaxial output, with SPDIF connector labeled COAX. This output can pass PCM data streams up to 24-bits long and up to 96 kHz sampling frequency.

9Digital Audio Output - Optical

These digital outputs carry only digital audio data, excluding any sub- code information which some recorders might use to extract CD track information.

107.1-Channel Analog Audio Inputs

These inputs are designed for any multi-channel source with analog outputs, such as SACD players. When connecting the analog audio inputs, make sure to attach each cable from the source component output to the appropriate SSP input.

Starting from the source, connect the Front Left output to the FL (Front

Left) input of the SSP, then the source center output to the CEN (center) input of the SSP, and so on.

These analog audio input signals are passed through the SSP and to the speakers with no processing. When these inputs are selected, only volume control is enabled.

112-Channel Balanced Analog Audio Inputs

The SSP-800/CT-SSP was designed with a 2-channel balanced analog audio input, using a pair of balanced XLR connectors labeled R1 and L1. Use this input with any 2-channel analog source component with balanced outputs.

NOTE: This input conforms to the AES (Audio Engineering

Society) “pin 2 = hot” convention. The pin assignments of these

XLR-type female output connectors are:

Pin 1: Signal ground

Pin 2: Signal + (non-inverting)

Pin 3: Signal – (inverting)

Connector ground lug: chassis ground

Verify that the source components are compliant with this convention (Classé components are compliant). If not compliant, contact your Classé dealer for assistance.

122-Channel Single-Ended Analog Audio Inputs

The SSP-800/CT-SSP was designed with a pair of 2-channel single- ended analog audio inputs using the RCA connectors, labeled L2/R2 and L3/R3. Use these inputs with any 2-channelsingle-ended analog source component.

NOTE: The Balanced and Single Ended 2-channel analog audio inputs can be set for either bypass mode (no DSP processing) or converted to digital format to allow bass management, surround mode processing, and/or equalization.

Image 20
Contents SSP-800/CT-SSP Surround Sound ProcessorClass Important Safety Instructions Contents Name PlayLinkIntroduction Welcome to the Classé familyExceptional Design Features Page Unpacking and Placement Unpacking your SSPNON-RACK-MOUNT Installation for SSP Tighten to In-lbs 0.96 N-m Warm-up/break-in period Operating voltage Voltage protection Standby/On Button and Status Indicator Front PanelsMenu On/Off Button TouchscreenAudio Mute Control IR windowVolume Control Knob Composite Video Inputs Rear PanelSerial number Component Video Inputs Hdmi InputsHdmi Outputs Component Video OutputDigital Audio Inputs Coaxial Digital Audio Inputs OpticalDigital Audio Output Coaxial Digital Audio Output Optical10 7.1-Channel Analog Audio Inputs 11 2-Channel Balanced Analog Audio InputsIR Input IR OutputTrigger Outputs USB Port 17 RS-232 PortCAN-Bus Input and Output 19 10-Channel Analog OutputsMain Power On/Off Switch AC Power Cord InputRemote Control Basic FunctionsAudio Processing Functions Input Sel Selection ButtonPreset Config Configuration Button Volume Control & Mute ButtonsNavigation & Menu Buttons Function Keys F1 to F4Choose the appropriate cables Initial SetupStep Connect all source components to the SSP rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name Post-processing Dolby TrueHDUsing the SSP-800/CT-SSP Source selectionMode selection Name DescriptionDTS Neo6 Cinema Controls System trimsConfiguration select Menu System System setup Volume setupMax volume Startup volume IR setup Automation Mute setup Input setup NameAudio Configuration Use Video Next input TriggersProfiles Room EQ Configuration Name Distances Levels Use SpeakersSpeakers available Auxiliary channels Teach IR Display setup Black levelBrightness Timeout Language OSD on screen display Colors Volume Dolby/DTSDolby Pro Logic DTS Neo6 Dolby Volume Remote Fkeys Important note on Fkey useFeatures Version info SensorsHardware setup Classé Delta Series ProductsCategory 5 Network Cables CAN-Bus TerminatorUsing CAN-Bus CAN-Bus shared features Configuration Operate AC status Status PlayLink Amp info Event log There is no sound and the Standby LED is not lit TroubleshootingEverything appears to be powered on, but there is no sound IR remote control does not seem to function Only one speaker seems to be playingThere is a hum coming out of the speakers There is a hum coming from the SSPVoltage Protection Circuit Care & Maintenance Input factory defaultsSpecifications Overall dimensionsNet weight Shipping weightSSP-800 Dimensions CT-SSP Dimensions Installation Worksheet Lachine, Quebec Canada H8T 1B3