Classe Audio SSP-800/CT-SSP owner manual Voltage Protection Circuit

Page 64

64

PIf there is no output on component video from an HDMI source, the signal is likely HDCP encrypted. Try setting the source up with an analog cable and select an analog video input path.

PIf there is a preview image but no output image, check the display connection. Ensure the YPrPb cables are properly connected if using a component video TV. Some display devices may not display the source’s output resolution (for example, component 720p going into a standard definition display or an HDMI source which is preset to an unsupported resolution for a particular HDMI display.

PIf the preview image looks good but the colors are wrong on the component video display then check that the component cables are properly connected. NOTE: Only a non-copy protected YCrCb HDMI source can be viewed on a component display. Other types of HDMI sources show either no picture or improper colors.

8 Voltage Protection Circuit

When the SSP is connected to AC power, the AC input enters the component through a Voltage Sensing Circuit, which checks the voltage level every 25 milliseconds. Power can only reach the component once it has passed the Voltage Sensing Circuit. The circuit verifies that the power is within tolerable operating levels:

Pof ±10% of its AC line voltage setting.

Pbetween ± 11% and 15% of its AC line voltage setting.

The following behavior of the SSP is the result of the Voltage Sensing Circuit:

PIf the external voltage is within the performance range, the product functions normally.

PIf the external voltage enters the range of the safe operating limit, the standby LED flashes every half-second but the product otherwise continues to function normally.

PIf the external voltage exceeds the safe operating limit for

10 consecutive seconds, the protection circuitry engages and an error message appears on the touchscreen.

PIf the external voltage falls below its performance range, the standby LED flashes indefinitely every half-second until the voltage is insufficient to sustain normal operation.

PYou have to cycle power to reset the protection circuitry. If you attempt to reset the SSP while the external power supply remains

outside the safe operating limit, the protection circuit re- engages, putting the SSP back into Standby mode. We therefore recommend that you wait until the standby LED stops flashing before cycling power and resetting the protection circuitry.

Page 63 Page 65
Image 64
Page 63 Page 65
Contents SSP-800/CT-SSP Surround Sound ProcessorClass Important Safety Instructions Contents Name PlayLinkIntroduction Welcome to the Classé familyExceptional Design Features Page Unpacking and Placement Unpacking your SSPNON-RACK-MOUNT Installation for SSP Tighten to In-lbs 0.96 N-m Warm-up/break-in period Operating voltage Voltage protection Standby/On Button and Status Indicator Front PanelsMenu On/Off Button TouchscreenAudio Mute Control IR windowVolume Control Knob Serial number Rear PanelComposite Video Inputs Component Video Inputs Hdmi InputsHdmi Outputs Component Video OutputDigital Audio Inputs Coaxial Digital Audio Inputs OpticalDigital Audio Output Coaxial Digital Audio Output Optical10 7.1-Channel Analog Audio Inputs 11 2-Channel Balanced Analog Audio InputsIR Input IR OutputTrigger Outputs USB Port 17 RS-232 PortCAN-Bus Input and Output 19 10-Channel Analog OutputsMain Power On/Off Switch AC Power Cord InputRemote Control Basic FunctionsAudio Processing Functions Input Sel Selection ButtonPreset Config Configuration Button Volume Control & Mute ButtonsNavigation & Menu Buttons Function Keys F1 to F4Step Initial SetupChoose the appropriate cables Connect all source components to the SSP rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name Post-processing Dolby TrueHDUsing the SSP-800/CT-SSP Source selectionMode selection Name DescriptionDTS Neo6 Cinema Controls System trimsConfiguration select Menu System System setup Volume setupMax volume Startup volume IR setup Automation Mute setup Input setup NameAudio Configuration Use Video Next input TriggersProfiles Room EQ Configuration Name Distances Levels Use SpeakersSpeakers available Auxiliary channels Teach IR Display setup Black levelBrightness Timeout Language OSD on screen display Colors Volume Dolby/DTSDolby Pro Logic DTS Neo6 Dolby Volume Remote Fkeys Important note on Fkey useFeatures Version info SensorsHardware setup Classé Delta Series ProductsCategory 5 Network Cables CAN-Bus TerminatorUsing CAN-Bus CAN-Bus shared features Configuration Operate AC status Status PlayLink Amp info Event log Everything appears to be powered on, but there is no sound TroubleshootingThere is no sound and the Standby LED is not lit IR remote control does not seem to function Only one speaker seems to be playingThere is a hum coming out of the speakers There is a hum coming from the SSPVoltage Protection Circuit Care & Maintenance Input factory defaultsSpecifications Overall dimensionsNet weight Shipping weightSSP-800 Dimensions CT-SSP Dimensions Installation Worksheet Lachine, Quebec Canada H8T 1B3
Top Page Image Contents