Classe Audio SSP-800/CT-SSP owner manual Terminals to black terminals

Page 28

Step 5

Important!

28

Connect the Main Analog Audio Outputs, either RCA or XLR, from the rear panel of the SSP to the corresponding inputs on your amplifier(s) as follows:

•Connect the SSP Front Left and Front Right outputs to the inputs of the amplifier(s) designated for the Front Left and Front Right speakers, respectively.

•Connect the SSP center output to the input of the amplifier designated for the center channel speaker.

•Connect the SSP Left Surround and Right Surround outputs to the inputs of the amplifier(s) designated for the Left Surround and Right Surround speakers, respectively.

•If you are setting up a 7.1-channel system, then also connect the SSP

Left Rear and Right Rear outputs to the inputs of the amplifier(s) designated for the Left Rear and Right Rear speakers, respectively.

•If you are using a subwoofer, connect the SSP subwoofer output to the input of the designated amplifier or powered subwoofer.

NOTE: Make sure connections from the subwoofer output go only to an amplifier connected to a subwoofer, as low frequency signals can damage a small full-range speaker not designed for high output bass reproduction.

Verify that each cable is clearly labeled so that you don’t mix them up. When connecting a cable, make sure the cable has a good connection and is firmly attached to the rear panel connectors on both the amplifier and the SSP.

The SSP-800/CT-SSP also provides two Auxiliary analog audio outputs. See the Rear Panel section for more details about the Auxiliary outputs.

Connect the loudspeakers to the amplifiers.

Verify that the power amplifier(s) is plugged in but powered OFF before connecting to the SSP!

Connect each loudspeaker to its designated amplifier(s) channel. Pay close attention to the phase of the speaker connections – always connect an amplifier’s red (+) terminals to the red (+) terminals of the loudspeaker. Likewise, connect black

(–) terminals to black (–) terminals.

Image 28

Contents SSP-800/CT-SSP Surround Sound ProcessorClass Important Safety Instructions Contents Name PlayLinkIntroduction Welcome to the Classé familyExceptional Design Features Page Unpacking and Placement Unpacking your SSPNON-RACK-MOUNT Installation for SSP Tighten to In-lbs 0.96 N-m Warm-up/break-in period Operating voltage Voltage protection Standby/On Button and Status Indicator Front PanelsMenu On/Off Button TouchscreenAudio Mute Control IR windowVolume Control Knob Serial number Rear PanelComposite Video Inputs Component Video Inputs Hdmi InputsHdmi Outputs Component Video OutputDigital Audio Inputs Coaxial Digital Audio Inputs OpticalDigital Audio Output Coaxial Digital Audio Output Optical10 7.1-Channel Analog Audio Inputs 11 2-Channel Balanced Analog Audio InputsIR Input IR OutputTrigger Outputs USB Port 17 RS-232 PortCAN-Bus Input and Output 19 10-Channel Analog OutputsMain Power On/Off Switch AC Power Cord InputRemote Control Basic FunctionsAudio Processing Functions Input Sel Selection ButtonPreset Config Configuration Button Volume Control & Mute ButtonsNavigation & Menu Buttons Function Keys F1 to F4Step Initial SetupChoose the appropriate cables Connect all source components to the SSP rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name Post-processing Dolby TrueHDUsing the SSP-800/CT-SSP Source selectionMode selection Name DescriptionDTS Neo6 Cinema Controls System trimsConfiguration select Menu System System setup Volume setupMax volume Startup volume IR setup Automation Mute setup Input setup NameAudio Configuration Use Video Next input TriggersProfiles Room EQ Configuration Name Distances Levels Use SpeakersSpeakers available Auxiliary channels Teach IR Display setup Black levelBrightness Timeout Language OSD on screen display Colors Volume Dolby/DTSDolby Pro Logic DTS Neo6 Dolby Volume Remote Fkeys Important note on Fkey useFeatures Version info SensorsHardware setup Classé Delta Series ProductsCategory 5 Network Cables CAN-Bus TerminatorUsing CAN-Bus CAN-Bus shared features Configuration Operate AC status Status PlayLink Amp info Event log Everything appears to be powered on, but there is no sound TroubleshootingThere is no sound and the Standby LED is not lit IR remote control does not seem to function Only one speaker seems to be playingThere is a hum coming out of the speakers There is a hum coming from the SSPVoltage Protection Circuit Care & Maintenance Input factory defaultsSpecifications Overall dimensionsNet weight Shipping weightSSP-800 Dimensions CT-SSP Dimensions Installation Worksheet Lachine, Quebec Canada H8T 1B3