Classe Audio SSP-800/CT-SSP owner manual CAN-Bus Input and Output, 19 10-Channel Analog Outputs

Page 22

22

18CAN-Bus Input and Output

CAN-Bus (Controller Area Network) allows several Classé components to be connected together for simultaneous operation, such as switching from On to Standby. Using the CAN-Bus Input and Output connectors, the

Classé components can be daisy chained together and controlled via the

CAN-Bus interface.

NOTE: The final component in the daisy chain MUST have a termination plug inserted into the CAN-Bus output.

For more information, refer to the CAN-Bus section found later in this

manual.

1910-Channel Analog Outputs

The SSP supports ten analog audio outputs, with both balanced (XLR) and single-ended (RCA) connections. Connect the appropriate Front L/R, Sub, Surr L/R, and Rear L/R connectors to the appropriate power amplifiers.

NOTE: The Rear L/R connectors are only active when the SSP output is setup for a 7.1-channel surround system and the audio stream or the selected surround processing mode are providing rear channel signals.

The Aux 1 and 2 outputs are programmable and can be used for the following purposes:

Assigned as a 2-channel down-mix of the selected multi-channel signal for either an analog recorder or a separate listening area.

Assigned to follow the main Front L/R speakers for use in a biamplification arrangement.

One or both may be assigned as additional subwoofers with the ability to select between mono, and stereo modes.

Refer to the Menu System section for more details regarding optional uses for the auxiliary analog output channels.

NOTE: The Balanced (XLR) Output pin assignments adhere to the AES (Audio Engineering Society) “Pin 2 = hot” standard. The XLR male outputs carry the following pin assignments:

Pin 1: Signal ground

Pin 2: Signal + (non-inverting)

Pin 3: Signal – (inverting)

Connector ground lug: chassis ground

Refer to the operating manuals of your balanced-input power amplifiers to verify that the pin assignments of their input connectors adhere to this standard (Classé power amplifiers are compliant). If your amplifiers are not compliant, ask your Classé dealer for assistance.

Image 22
Contents SSP-800/CT-SSP Surround Sound ProcessorClass Important Safety Instructions Contents Name PlayLinkIntroduction Welcome to the Classé familyExceptional Design Features Page Unpacking and Placement Unpacking your SSPNON-RACK-MOUNT Installation for SSP Tighten to In-lbs 0.96 N-m Warm-up/break-in period Operating voltage Voltage protection Standby/On Button and Status Indicator Front PanelsAudio Mute Control Menu On/Off ButtonTouchscreen IR windowVolume Control Knob Serial number Rear PanelComposite Video Inputs Component Video Inputs Hdmi InputsDigital Audio Inputs Coaxial Hdmi OutputsComponent Video Output Digital Audio Inputs Optical10 7.1-Channel Analog Audio Inputs Digital Audio Output CoaxialDigital Audio Output Optical 11 2-Channel Balanced Analog Audio InputsTrigger Outputs IR InputIR Output USB Port 17 RS-232 PortCAN-Bus Input and Output 19 10-Channel Analog OutputsMain Power On/Off Switch AC Power Cord InputAudio Processing Functions Remote ControlBasic Functions Input Sel Selection ButtonNavigation & Menu Buttons Preset Config Configuration ButtonVolume Control & Mute Buttons Function Keys F1 to F4Step Initial SetupChoose the appropriate cables Connect all source components to the SSP rear panel Terminals to black terminals Power up the system Understanding Surround Sound Name Post-processing Dolby TrueHDUsing the SSP-800/CT-SSP Source selectionMode selection Name DescriptionDTS Neo6 Cinema Controls System trimsConfiguration select Menu System System setup Volume setupMax volume Startup volume IR setup Automation Mute setup Input setup NameAudio Configuration Use Video Next input TriggersProfiles Room EQ Configuration Name Distances Levels Use SpeakersSpeakers available Auxiliary channels Teach IR Display setup Black levelBrightness Timeout Language OSD on screen display Colors Volume Dolby/DTSDolby Pro Logic DTS Neo6 Dolby Volume Remote Fkeys Important note on Fkey useFeatures Version info SensorsCategory 5 Network Cables Hardware setupClassé Delta Series Products CAN-Bus TerminatorUsing CAN-Bus CAN-Bus shared features Configuration Operate AC status Status PlayLink Amp info Event log Everything appears to be powered on, but there is no sound TroubleshootingThere is no sound and the Standby LED is not lit There is a hum coming out of the speakers IR remote control does not seem to functionOnly one speaker seems to be playing There is a hum coming from the SSPVoltage Protection Circuit Care & Maintenance Input factory defaultsNet weight SpecificationsOverall dimensions Shipping weightSSP-800 Dimensions CT-SSP Dimensions Installation Worksheet Lachine, Quebec Canada H8T 1B3