4.Place one of the Handrail Spacers (65) on the right Upright (69) as shown, with the cutout turned toward the treadmill (see inset drawing A). Pull the Upright Wire Harness (98) up through the Handrail Spacer. Place the other Handrail Spacer on the left Upright (not shown).
Have a second person hold the Handrails (66) near the
Uprights (69) as shown. Connect the Upright Wire
Harness (98) to the wires extending from the right
Handrail. Insert the connectors and the Wire Harness
(98)into the hole in the Console Base (81) (see inset drawing B).
Be careful not to pinch the Wire Harness (98) as you set the Handrails (66) on the Spacers (65).
5.Insert two Handrail Bushings (75) into the right Upright (69). Turn the Handrail Bushings so they fit against the Upright with the thick sides of the Bushings facing the centre of the treadmill as shown in the inset drawing.
Insert two Handrail Bolts (78) with Handrail Washers
(77)into the Handrail Bushings (75), the right Upright (69), and the right Handrail Spacer (65). Lift up the right Handrail (66) to align the Bolts with the holes in the Handrail. Next, thread the Bolts into the Handrail (66).
Do not tighten the Bolts yet.
Attach the left Handrail (not shown) in the same way.
Tighten all four Handrail Bolts (78).
6.Look at the Endcap (58). If the left or right foot on the Endcap does not touch the floor, the included thick
base pads should be attached to the treadmill as de- scribed below.
Refer to assembly step 3. Lower the treadmill frame
and the Uprights (69) as shown. If the | left foot of the | |||
Endcap (58) was off the ground, remove the two Base | ||||
Pads (99) from the | right | Upright (69). Attach the in- | ||
cluded Thick Base Pads (not shown) to the Upright. If | ||||
the right | side of the Endcap was off the ground, attach | |||
the Thick Base Pads to the |
| left | Upright. | |
Note: If either side of the Endcap (58) lifts off the floor when the treadmill is used, attach the Thick Base Pads
as described.
4 | Cutout | A |
|
|
| 81 |
|
|
|
| 66 |
| 69 | |
|
|
|
| |
|
|
|
| 65 |
| 98 69 | B | 98 |
|
| 65 |
|
|
|
|
|
|
| 81 |
5 |
|
|
|
|
|
| 66 |
|
|
| 65 |
|
| |
|
| 69 |
|
|
|
| 75 |
|
|
|
|
| 77 | Thick |
|
|
| Side | |
|
|
|
| |
| 75 |
|
|
|
| 77 |
| 78 |
|
6 |
|
|
|
|
Left |
|
|
|
|
Foot | 58 |
|
|
|
|
|
|
| |
|
|
|
| Right |
|
|
|
| Foot |
7. Make sure that all parts are tightened before you use the treadmill. | Note: If there is a thin sheet of clear |
plastic on the hood decal or the “ComforTrack” decal, remove it. K | eep the included allen wrench in a secure |
place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet from damage, place a mat under the treadmill.
7