Gold's Gym GGBE6974.1 manual Button Screws yet, Repeat this step with the other Side Top Frame

Page 11

9.

Insert a Side Rod Cap (33) into a Side Top Frame

9

 

90

 

 

 

 

(13). Set the Top Frame onto the left Guide Rod

 

 

 

 

 

 

 

 

 

 

 

(5) and insert it into the Left Support (6).

 

 

 

 

 

 

 

Attach the Side Top Frame (13) to the Left

 

 

 

 

 

13

 

 

 

 

 

 

 

 

Upright (3) and the Left Support (6) with two M10

 

 

84

 

 

 

 

x 73mm Button Screws (103), two M10 x 25mm

 

 

 

 

 

 

 

Button Screws (98), four M10 Split Washers (93),

 

 

79

 

 

 

 

and four M10 Washers (84). Do not tighten the

 

 

 

 

 

 

 

Button Screws yet.

 

 

 

33

 

 

 

Insert an M10 x 67mm Button Bolt (90) through

84

 

5

 

93

98

 

the Left Upright (3) and the Side Top Frame (13).

 

 

 

 

 

 

 

84

 

 

Hand tighten an M10 Washer (84) and an M10

 

 

 

 

 

 

 

 

 

 

 

 

 

Nylon Locknut (79) onto the Button Bolt.

93 3

 

 

 

6

 

 

 

 

 

 

 

 

 

Repeat this step with the other Side Top Frame

103

 

 

 

 

 

 

 

 

 

 

 

 

 

(13) and the right side of the weight rack.

 

 

 

 

 

 

10.

Orient the Center Top Frame (14) with the decal

10

 

 

 

 

 

 

in the position shown. Make sure that the Rod

 

 

 

 

 

 

 

14

97

 

 

 

 

Cap (33) is inside of the left Side Top Frame

 

 

 

 

 

 

 

 

 

 

 

(13).

 

 

 

 

 

 

 

Attach the Center Top Frame (14) to the Side Top

Decal

 

 

66

 

 

 

 

 

 

 

 

 

 

97

 

13

 

 

Frame (13) with two M10 x 93mm Button Bolts

 

 

 

 

 

 

 

 

 

 

 

(97), two 17mm Spacers (66), two M10 Washers

 

 

 

 

 

 

 

(84), and two M10 Nylon Locknuts (79). Do not

 

 

 

 

66

 

 

tighten the Nylon Locknuts yet.

 

 

 

 

 

 

Repeat this step with the right Side Top Frame

 

 

 

33

 

 

 

(not shown).

 

 

 

84

79

 

 

 

 

 

 

 

 

11.

Attach a Support Frame (15) to the left Side Top

11

 

 

79

 

 

 

Frame (13) with two M10 x 93mm Button Bolts

 

 

 

 

 

 

 

 

 

 

 

(97), two M10 Washers (84), and two M10 Nylon

13

8

 

15

97

 

 

Locknuts (79). Do not tighten the Nylon

 

 

 

 

15

 

 

 

 

Locknuts yet.

92

 

 

 

 

 

 

 

 

 

 

 

 

Attach the other Support Frame (15) to the

 

 

 

79

 

 

 

 

 

 

 

 

 

 

right Side Top Frame (13) in the same manner.

92

 

 

97

 

 

 

Attach the two Support Frames (15) to the

 

 

 

 

13

 

 

Backrest Upright (8) with two M10 x 95mm Button

 

 

 

 

 

 

 

 

 

 

 

 

 

Bolts (92) and two M10 Nylon Locknuts (79). Do

 

 

 

 

 

 

 

not tighten the Nylon Locknuts yet.

 

 

 

 

 

 

 

 

 

 

 

 

84

79

 

 

11

 

 

 

 

 

Image 11
Contents Call TOLL-FREE QUESTIONS?Model No. GGBE6974.1 Serial No Table of Contents Important Precautions Relative to a person sitting on the bench they do not corre Before YOU BeginRight Side Left SidePart Identification Chart Page Make Assembly Easier AssemblyPage Do not tighten the Nylon Locknut yet See the inset drawing. Identify the Guide RodsGuide not shown Cap 33 is inside of the left Side Top Frame Right side of the weight rackButton Screws yet Repeat this step with the other Side Top FrameNylon Locknuts yet Repeat this step with the Right ArmPage Nylon Locknut the Cable must pivot easi Page Identify the Low Cable 72. Route the Cable Page Page Page Page Page Page Do not tighten the Nylon Locknuts yet 124 Attaching Accessories AdjustmentUsing the Weight BAR Adjusting the Weight RestsAdjusting the Spotters Adjusting the Seat Adding WeightAdjusting the Backrest Attaching the Curl BAR Adjusting the Backrest PADAttaching the Curl PAD KnobButterfly Cable Cable DiagramsLong Cable Low Cable High CableTightening the Cables MaintenanceExercise Guidelines Staying Motivated Muscle ChartCooling Down Qty Description Part LIST-Model No. GGBE6974.1111 Exploded Drawing A-Model No. GGBE6974.1 Exploded Drawing B-Model No. GGBE6974.1 R1107A Exploded Drawing C-Model No. GGBE6974.1 R1107A Exploded Drawing D-Model No. GGBE6974.1 R1107A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty