Precor C934 Setting Up the Treadmill, Installation Requirements, Assembly Instructions

Page 11

C O M M E R C I A L P R O D U C T S D I V I S I O N

Setting Up the Treadmill

You do not need any special knowledge or experience to set up the treadmill. However, because of the size and weight of the treadmill, you will need to obtain assistance.

INSTALLATION REQUIREMENTS

Follow these installation requirements when installing the treadmill. If you do not install the treadmill according to the following guidelines, you could void the Precor limited warranty.

•Set up the treadmill on a solid, flat surface. Unpack and assemble the treadmill close to where you plan to use it. Make sure that the flat surface under the unit is smooth and level. A level unit is required for the user’s safety and proper operation.

•Provide ample space around the unit. Open space around the unit makes for a safer mount and dismount.

•Fill out and mail the limited warranty card. Be sure that the treadmill is turned OFF. The serial number can be found on the shipping container or on the label near the power receptacle. Write the serial number onto the Precor limited warranty card found on the back cover of this manual. Refer to Obtain- ing Service on page 7 and write the number(s) there as well.

•Use the appropriate voltage, dedicated circuit, and grounding as speci- fied on the treadmill. The treadmill is available in both 120-volt and 240-volt models. Refer to the treadmill’s identification label to determine the voltage that your treadmill requires. Both the 120-volt and 240-volt models require a dedicated circuit. A 20 amp circuit is recommended.

CAUTION: Do not use a non-grounded outlet or transformer. Do not remove or otherwise bypass the plug with an adapter. Electrical dam- age can occur and void the Precor limited warranty if the treadmill is connected to an improper power source.

ASSEMBLY INSTRUCTIONS

Take the following steps to assemble the treadmill.

1.Obtain adult assistance. Have your assistants help place the shipping carton close to the location where you plan to use the treadmill. Break down the side walls of the shipping carton so that they lie flat. Remove the loose contents.

CAUTION: To avoid injury and ensure your safety, get assistance be- fore lifting the treadmill off the pallet and rolling it onto the floor. Do not drop the unit.

2.Make sure that the power switch is OFF. Check the ON/OFF power switch on the front of the treadmill. Place the switch in the O (OFF) position. Make sure that the treadmill is not plugged into a power source.

page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents C934 Important Safety Instructions Grounding Instructions Safety ApprovalTable of Contents Courses MaintenanceExercising on the Treadmill Void the user’s authority to operate the equipment Radio Frequency Interference RFIEuropean Applications About this Manual Obtaining ServiceM M E R C I a L P R O D U C T S D I V I S I O N Other Equipment Unpacking the TreadmillStandard Equipment Additional Tools Needed Hardware KITAssembly Instructions Setting Up the TreadmillInstallation Requirements Diagram Route cable Csafe Secure the display console to the upright supports. DiagramRaise Perform steps a. and b. on the opposite side Attach handrails to the side and base brackets. DiagramTest the heart rate feature. Diagram Continue with the assembly Second Level Unit Turning the Unit on and OFF If the running belt Then Checking the Alignment of the Running BeltClub Information Changing the Club SettingsDetermining the Units of Measure Display key functions within the Club Custom ModeTo 18 kph Setting a Workout Time LimitSetting a Pause Time Limit Determining the Club Speed LimitM M E R C I a L P R O D U C T S D I V I S I O N User ID Entry Program Keys Using Csafe Standard EquipmentC934 Display Features on the Display ConsoleSmartrate Display Setup Mode and PromptsPrecor banner Course prompt Setup Mode and the Quickstart FeatureWeight prompt Following occurs Display Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keypad keys Keys on the Display ConsolePrompts Default Value Quickstart Default ValuesChanging the Display Features Using the Select KEY Exercising on the Treadmill Using the Security ClipUsing the Handrails Using the Heart Rate Touch CapabilityQuick Steps to Working OUT Keypad TipsWorkout Tips To display the course selections, press Enter and then Stop Cooling Down After a WorkoutStop PAUSE, Workout SUMMARY, and Exit FeaturesCourses Heart Rate FeatureUsing the Smartrate Feature Rate Manual Mode and the Quickstart KEYTo use the interval course, take the following steps Cross Country CourseInterval Course Random Course Weight Loss CourseHeart Rate Course Perform a daily inspection of the treadmill MaintenanceCleaning the Equipment InspectionAligning the Running Belt Long Term Storage Storing the Polar Chest StrapServicing the Treadmill C934 C934 C934 C934 C934 C934 C934 C934 Thank You and Welcome to Precor How many members do you have? Date of Purchase Purchased from Dealer nameProduct Serial Numbers Please indicate the type and number of products purchasedComplete this portion and keep for your records Limited WarrantyWarranty Periods and Coverage Conditions and RestrictionsC934 Programs C934 Display Readouts Product Specifications Electronic Specifications
Top Page Image Contents