Precor C934 owner manual M M E R C I a L P R O D U C T S D I V I S I O N

Page 32

C O M M E R C I A L P R O D U C T S D I V I S I O N

CALORIES: Provides the cumulative number of calories being burned by the user.

INCLINE: Displays the selected percent of incline during a workout. The INCLINE

▲and ▼ keys affect the treadmill’s lift and let the user set an incline between 0 percent and 15 percent. The displayed values change in 0.5 percent increments. Refer to INCLINE ▲▼ keys on page 33.

When the INCLINE field is selected and the target incline changes from the actual incline (as in a preprogrammed course), the target incline appears in the display. It continues to be displayed as the lift moves to the new incline level. A few seconds after the lift reaches the requested incline, the display no longer appears.

Note: To check the incline (when it is not the chosen display) any time during a workout, lightly press either INCLINE ▲ or ▼ key for less than two seconds. If a user presses the INCLINE ▲ or ▼ key for more than two seconds, the treadmill’s incline will change.

COURSE PROFILE: At the beginning of a course, the profile appears on the right side of the display and corresponds to the course that the user selected. As the user proceeds through his or her workout, the position in the course is indi- cated by a blinking column.The height of the column indicates the level of incline. Every time the incline changes by several sequential levels (up or down) the height of the column changes by one cell.

CALORIES PER MINUTE: Indicates the approximate number of calories being burned per minute.

METS: Displays the metabolic equivalents associated with a user’s current energy expenditure level. A METS level of 1 represents the body at rest. Note that when the running belt stops moving, the METS value displays zero.

SPEED: Displays the running belt’s speed. The running belt speed ranges from

0.5to 11 mph (1 to 18 kph), but a maximum speed can be set by the club (see Club Information on page 23). The SPEED ▼▲ keys let a user decrease or increase the running belt’s speed in 0.1 increments.

Important: To check the speed (when it is not the chosen display) any time during a workout, the user can lightly press either SPEED ▼ or ▲ key (for less than two seconds). The running belt’s speed appears in the right portion of the display. If a user presses the SPEED ▼ or ▲ key for more than two seconds, the treadmill’s speed will change.

PACE: Displays the user’s target speed in minutes and seconds per mile (or kilome- ter).The user’s pace appears in theTIME field when the SPEED indicator is not lit and the user taps the SPEED ▼ or ▲ key.

page 32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents C934 Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents Courses MaintenanceExercising on the Treadmill Void the user’s authority to operate the equipment Radio Frequency Interference RFIEuropean Applications Obtaining Service About this ManualM M E R C I a L P R O D U C T S D I V I S I O N Other Equipment Unpacking the TreadmillStandard Equipment Hardware KIT Additional Tools NeededAssembly Instructions Setting Up the TreadmillInstallation Requirements Diagram Route cable Secure the display console to the upright supports. Diagram CsafeRaise Attach handrails to the side and base brackets. Diagram Perform steps a. and b. on the opposite sideTest the heart rate feature. Diagram Continue with the assembly Second Level Unit Turning the Unit on and OFF Checking the Alignment of the Running Belt If the running belt ThenChanging the Club Settings Club InformationDisplay key functions within the Club Custom Mode Determining the Units of MeasureSetting a Workout Time Limit Setting a Pause Time LimitDetermining the Club Speed Limit To 18 kphM M E R C I a L P R O D U C T S D I V I S I O N Using Csafe Standard Equipment User ID Entry Program KeysFeatures on the Display Console C934 DisplaySetup Mode and Prompts Smartrate DisplayPrecor banner Course prompt Setup Mode and the Quickstart FeatureWeight prompt Following occurs Display Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad keysQuickstart Default Values Prompts Default ValueChanging the Display Features Using the Select KEY Using the Security Clip Using the HandrailsUsing the Heart Rate Touch Capability Exercising on the TreadmillQuick Steps to Working OUT Keypad TipsWorkout Tips To display the course selections, press Enter and then Cooling Down After a Workout StopPAUSE, Workout SUMMARY, and Exit Features StopCourses Heart Rate FeatureUsing the Smartrate Feature Manual Mode and the Quickstart KEY RateTo use the interval course, take the following steps Cross Country CourseInterval Course Weight Loss Course Random CourseHeart Rate Course Maintenance Cleaning the EquipmentInspection Perform a daily inspection of the treadmillAligning the Running Belt Long Term Storage Storing the Polar Chest StrapServicing the Treadmill C934 C934 C934 C934 C934 C934 C934 C934 Thank You and Welcome to Precor Date of Purchase Purchased from Dealer name Product Serial NumbersPlease indicate the type and number of products purchased How many members do you have?Limited Warranty Warranty Periods and CoverageConditions and Restrictions Complete this portion and keep for your recordsProduct Specifications Electronic Specifications C934 Programs C934 Display Readouts
Top Page Image Contents