Precor C934 owner manual Continue with the assembly

Page 18

C O M M E R C I A L P R O D U C T S D I V I S I O N

c. Place your left hand on the left handrail’s heart rate grip and place your right hand on the right handrail grip. The letters “Hr” begin to blink in the upper right display indicating that a signal is being transmitted. Within

	about 15 seconds a heart rate appears.
	Note: If the blinking “Hr” does not appear, turn the unit OFF. Recheck the
	cable connections and ask someone else to try the test (steps a through c).
	d. When the test is satisfactorily completed, turn OFF the treadmill and
	continue with the assembly.
Diagram 14	Install handrail
	clamp fasteners.
	Hand held heart
	rate grip

Lower handrail clamp

Replace the four fasteners removed in step 11.

Washer (F)

1½-inch screw (E)

15.Replace the lower handrail clamp. Diagram 14. Replace the lower handrail clamp and the four fasteners removed in step 11. Make sure the top of the handrail is aligned with the top portion of the clamp. Turn all four fasteners until they are finger tight.

16.Secure the handrails. Diagram 14. Place a large washer (F) onto each of two screws (E). Thread the screws through the lower handrail clamp and finger tighten.

page 18

Image 18

Contents C934 Important Safety Instructions Safety Approval Grounding InstructionsTable of Contents Maintenance Exercising on the TreadmillCourses Radio Frequency Interference RFI European ApplicationsVoid the user’s authority to operate the equipment Obtaining Service About this ManualM M E R C I a L P R O D U C T S D I V I S I O N Unpacking the Treadmill Standard EquipmentOther Equipment Hardware KIT Additional Tools NeededSetting Up the Treadmill Installation RequirementsAssembly Instructions Diagram Route cable Secure the display console to the upright supports. Diagram CsafeRaise Attach handrails to the side and base brackets. Diagram Perform steps a. and b. on the opposite sideTest the heart rate feature. Diagram Continue with the assembly Second Level Unit Turning the Unit on and OFF Checking the Alignment of the Running Belt If the running belt ThenChanging the Club Settings Club InformationDisplay key functions within the Club Custom Mode Determining the Units of MeasureDetermining the Club Speed Limit Setting a Workout Time LimitSetting a Pause Time Limit To 18 kphM M E R C I a L P R O D U C T S D I V I S I O N Using Csafe Standard Equipment User ID Entry Program KeysFeatures on the Display Console C934 DisplaySetup Mode and Prompts Smartrate DisplaySetup Mode and the Quickstart Feature Weight prompt Following occursPrecor banner Course prompt Display Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keys on the Display Console Keypad keysQuickstart Default Values Prompts Default ValueChanging the Display Features Using the Select KEY Using the Heart Rate Touch Capability Using the Security ClipUsing the Handrails Exercising on the TreadmillKeypad Tips Workout TipsQuick Steps to Working OUT To display the course selections, press Enter and then Cooling Down After a Workout StopPAUSE, Workout SUMMARY, and Exit Features StopHeart Rate Feature Using the Smartrate FeatureCourses Manual Mode and the Quickstart KEY RateCross Country Course Interval CourseTo use the interval course, take the following steps Weight Loss Course Random CourseHeart Rate Course Inspection MaintenanceCleaning the Equipment Perform a daily inspection of the treadmillAligning the Running Belt Storing the Polar Chest Strap Servicing the TreadmillLong Term Storage C934 C934 C934 C934 C934 C934 C934 C934 Thank You and Welcome to Precor Please indicate the type and number of products purchased Date of Purchase Purchased from Dealer nameProduct Serial Numbers How many members do you have?Conditions and Restrictions Limited WarrantyWarranty Periods and Coverage Complete this portion and keep for your recordsProduct Specifications Electronic Specifications C934 Programs C934 Display Readouts