Precor C934 owner manual Aligning the Running Belt

Page 47

C O M M E R C I A L P R O D U C T S D I V I S I O N

ALIGNING THE RUNNING BELT

The correct alignment of the running belt is critical to the smooth operation of the treadmill. The belt is properly aligned at the factory. However, during shipping and handling or by use on an uneven surface, the belt may move off center and require a few simple adjustments.

Before aligning the running belt, check its operation by following the procedure in Checking the Alignment of the Running Belt on page 22. If you determine that the belt needs alignment, follow the instructions here.

CAUTION: Special care must be taken when aligning the running belt.Turn OFF the treadmill while adjusting or working near the rear roller. Remove any loose clothing and tie back your hair. Be very careful to keep your finger or any other object clear of the belt and rollers, especially in front of the roller and behind the deck.The treadmill will not stop immediately if an object becomes caught in the belt or rollers.

Realigning the belt takes a few simple adjustments. If you are unsure about this procedure, call Precor Customer Support (see Obtaining Service on page 7.)

Take the following steps to align the running belt on the treadmill. To ensure your safety, make all adjustments while the treadmill is OFF.

1.Make sure the treadmill is OFF and the running belt has completely stopped.

2.Locate the left belt adjustment bolt in the rear end cap of the treadmill. (To determine left and right, stand at the rear of the treadmill and face the display.) The direction you turn the bolt depends on how the belt is tracking. Make all belt adjustments on the left rear corner bolt using the hex key provided.

•If the belt is off center to the LEFT, turn the adjusting bolt ¼ turn clock- wise, which moves the running belt to the right.

•If the belt tracks off center to the RIGHT, turn the bolt ¼ turn counter- clockwise; this moves the belt to the left.

Important: Do not turn the adjusting bolt more than ¼ turn at a time. Over- tightening the bolt can damage the treadmill.

3.Turn ON the treadmill, press QUICKSTART, and then increase the running belt speed to 3 mph (5 kph) by pressing SPEED ▲.

CAUTION: Stand to the side of the treadmill. The running belt begins moving automatically after you press QUICKSTART.

4.Observe the running belt for a couple of minutes. The belt should be centered on the running bed. A few inches from either side of the side rail platform.

CAUTION: If you hear any chafing or the running belt appears to be getting damaged, stop the running belt immediately by pressing the red Stop key. Contact Precor Customer Support.

5.If the belt needs additional alignment, repeat steps 1 through 4 of this procedure until the belt is properly aligned.

6.Press the red Stop button. To return to the Precor banner, press RESET.

page 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents C934 Important Safety Instructions Grounding Instructions Safety ApprovalTable of Contents Courses MaintenanceExercising on the Treadmill Void the user’s authority to operate the equipment Radio Frequency Interference RFIEuropean Applications About this Manual Obtaining ServiceM M E R C I a L P R O D U C T S D I V I S I O N Other Equipment Unpacking the TreadmillStandard Equipment Additional Tools Needed Hardware KITAssembly Instructions Setting Up the TreadmillInstallation Requirements Diagram Route cable Csafe Secure the display console to the upright supports. DiagramRaise Perform steps a. and b. on the opposite side Attach handrails to the side and base brackets. DiagramTest the heart rate feature. Diagram Continue with the assembly Second Level Unit Turning the Unit on and OFF If the running belt Then Checking the Alignment of the Running BeltClub Information Changing the Club SettingsDetermining the Units of Measure Display key functions within the Club Custom ModeTo 18 kph Setting a Workout Time LimitSetting a Pause Time Limit Determining the Club Speed LimitM M E R C I a L P R O D U C T S D I V I S I O N User ID Entry Program Keys Using Csafe Standard EquipmentC934 Display Features on the Display ConsoleSmartrate Display Setup Mode and PromptsPrecor banner Course prompt Setup Mode and the Quickstart FeatureWeight prompt Following occurs Display Features During a Workout M M E R C I a L P R O D U C T S D I V I S I O N Keypad keys Keys on the Display ConsolePrompts Default Value Quickstart Default ValuesChanging the Display Features Using the Select KEY Exercising on the Treadmill Using the Security ClipUsing the Handrails Using the Heart Rate Touch CapabilityQuick Steps to Working OUT Keypad TipsWorkout Tips To display the course selections, press Enter and then Stop Cooling Down After a WorkoutStop PAUSE, Workout SUMMARY, and Exit FeaturesCourses Heart Rate FeatureUsing the Smartrate Feature Rate Manual Mode and the Quickstart KEYTo use the interval course, take the following steps Cross Country CourseInterval Course Random Course Weight Loss CourseHeart Rate Course Perform a daily inspection of the treadmill MaintenanceCleaning the Equipment InspectionAligning the Running Belt Long Term Storage Storing the Polar Chest StrapServicing the Treadmill C934 C934 C934 C934 C934 C934 C934 C934 Thank You and Welcome to Precor How many members do you have? Date of Purchase Purchased from Dealer nameProduct Serial Numbers Please indicate the type and number of products purchasedComplete this portion and keep for your records Limited WarrantyWarranty Periods and Coverage Conditions and RestrictionsC934 Programs C934 Display Readouts Product Specifications Electronic Specifications
Top Page Image Contents