Precor EFX556 owner manual Setting Up the EFX, Installation Requirements, Assembly Instructions

Page 11

C O M M E R C I A L P R O D U C T S D I V I S I O N

Setting Up the EFX

You do not need any special knowledge or experience to set up the EFX. However, you will need assistance. Because of the size and weight of the EFX, it is recommended that at least three adult persons assemble it.

INSTALLATION REQUIREMENTS

Follow these installation requirements when installing the EFX. If you do not install the EFX according to the following guidelines, you could void the Precor limited warranty.

•Set up the EFX on a solid, flat surface. Unpack and assemble the EFX close to where you’ll use it. Make sure that the flat surface under the unit is smooth and level. A level unit is required for the user’s safety and for proper operation.

•Provide ample space around the unit. Open space around the unit makes for a safer mount and dismount.

•Fill out and mail the limited warranty card. Be sure that the EFX is turned OFF. To locate the serial number, kneel down alongside the EFX and look for a label inside the rear cover. Write the serial number onto the Precor limited warranty card found on the back cover of this manual. Refer to Obtaining Service on page 2 and write the number(s) there as well.

•Use the appropriate voltage, dedicated circuit, and grounding as speci- fied on the EFX556. The EFX556 is available in a 120-volt and a 240-volt model. Refer to the identification label next to the ON/OFF (I/O) switch to determine the voltage, power cord, and plug that your EFX556 requires. Make sure that the EFX556 is connected to a power outlet that has the same configuration as the plug.

CAUTION: Use the appropriate power cord and plug for your unit. Do not use a non-grounded outlet. Electrical damage can occur if the EFX556 is connected to an improper power source.

ASSEMBLY INSTRUCTIONS

You do not need any special knowledge or experience to set up an EFX556, however you will need assistance and certain tools. Because of its weight and size, ask for several assistants to help you assemble the EFX556.

To assist you in the assembly, the items in the hardware kit, shown in Diagram 1, correspond to a particular letter in the alphabet. These letters appear throughout the assembly instructions. Refer to Diagram 1, as needed.

1.Unpack the EFX556. Remove the packing materials and loose contents (upper console assembly with electronic console, hardware kit, bracket covers, handrails, and power cord) from inside the cardboard pockets and from around the base frame assembly.

2.Pull the large cardboard piece away from the base frame assembly. Ask for assistance to move the EFX556 off the shipping pallet.You may need to cut the tie wraps that hold the base frame and roller arms to the pallet.

3.Move the unit to the location where you plan to use it. Make sure that the EFX556 is unplugged and turned OFF. Do not assemble the EFX556 if it is plugged into a power outlet.

page 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents EFX About this Manual Obtaining ServiceBefore You Begin Important Safety Instructions Volt grounding plug Safety ApprovalGrounding Instructions European Applications 240 Volt Units Only RFI Radio Frequency InterferenceEuropean Applications Precor Heart Rate OPTIONS-SAFETY Guidelines Personal SafetyTable of Contents Workout Statistics Log MaintenanceExercising on the EFX CoursesOptional Equipment Unpacking the EFXStandard Equipment Acquire the Appropriate Tools Hardware KITAssembly Instructions Setting Up the EFXInstallation Requirements Diagram Diagram 4 Secure the console assembly to the base frame Level the unit Turning the EFX556 on and OFF Club Information Changing the Club SettingsDetermining the Units of Measure Display key functions within the Club Custom ModeSelecting the Language Setting a Pause Time Limit Setting a Workout Time LimitUser ID Entry Program Keys Using Csafe Standard EquipmentNumber keypad Enter Reset EFX556 Display Features on the Display ConsoleElongated Center Display TOP Display WindowsCenter Display Window M M E R C I a L P R O D U C T S D I V I S I O N Keypad Tips Keys on the Display ConsoleM M E R C I a L P R O D U C T S D I V I S I O N Press Quick Start at the,... The following occurs Quick Start Default ValuesExercising on the EFX Using the HandlebarsUsing the Stationary Handrails PAUSE, Cool Down and Exit FeaturesNo pedaling Is detected Cool down Mode This is what happensNo pedaling Pause Mode, you This is what happensAt Workout Summary Banner, you This is what happens Workout TipsQuick Steps to Working OUT Cooling Down After a Workout Courses Heart Rate FeatureUtilizing the Smart Rate Feature Heart Rate Training Zone Manual Mode and the Quick Start KEYTo use the interval course, take the following steps Cross Training CourseCross Country and Hill Climb Courses Interval CourseWeight Loss Course Servicing the EFX MaintenanceCleaning the Equipment Storing the Polar Chest StrapWorkout Statistics Log M M E R C I a L P R O D U C T S D I V I S I O N EFX View 2 March 6, 2000 Rev. B View 3 March 6, 2000 Rev. B View 4 March 6, 2000 Rev. B View 5 March 6, 2000 Rev. B View 6 March 6, 2000 Rev. B Commercial Equipment Limited Warranty Product Specifications Electronic Specifications Warranty Registration Card
Top Page Image Contents