Weider 831.159831 user manual On the Short Weight Tube, On the bottom

Page 10

13. Slide six Weights (41) onto the Right Weight

13

Guides (26). Make sure the Weights are turned

 

so the pin grooves are on the bottom.

 

Press a Weight Tube Bumper (45) into the lower

 

end of the Short Weight Tube (44). Slide the

26

Short Weight Tube into the center holes in the

42

Weights (41).

 

 

 

Slide a Top Weight (42) onto the Right Weight

 

Guides (26). Note: Make sure the Top Weight is

Welded

turned so the groove fits over the welded pin

Pin

on the Short Weight Tube (44).

44

 

 

 

 

41

 

 

45

 

 

Pin

 

 

Grooves

14. Slide the Bottom Weight (47) and seven Weights

14

(41) onto the Left Weight Guides (27).

Make sure

the Weights are turned so the pin grooves are

 

on the bottom.

 

 

Press a Weight Tube Bumper (45) into the lower

27

42

end of the Long Weight Tube (43). Slide the Long

 

Weight Tube into the center holes in the Weights

 

(41).

 

 

 

 

Welded

Slide the other Top Weight (42) onto the Left

Pin

Weight Guides (27).

Note: Make sure the Top

 

Weight is turned so the groove fits over the

43

welded pin on the Long Weight Tube (43).

 

 

 

45

 

 

41

 

 

Pin

 

 

Groove

 

 

47

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents SEARS, Roebuck and CO Hoffman ESTATES, IL Model No Serial NoSerial Number Decal Patent PendingTable of Contents Important Precautions Before YOU Begin Using the Power Stack weight systemDecal Arm Assembly AssemblyCable Assembly To open the parts bag for that stageLocate and open the parts bag labeled Frame AssemblyTape over the head of each Bolt 109 Onto the Bolts. Do not tighten the Nylon Locknuts yet100 Do not Tighten the Nylon Locknuts yet YetLocknuts 86. Do not tighten the Nylon Locknuts yet On bottom Press a 2 Square Inner Cap 67 into the Press Top FrameInto On the Short Weight Tube On the bottomNylon Locknuts yet Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon JamnutsAssembly Bag for identification of the Pro Pulleys Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bracket onEd as shown Labeled Pulley BAGBracket On the back of the Butterfly Upright Identify the Rear Cable103 Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright Large tabsGroove of the Pulley Remove the 3 1/2 Pulleys 35 from the otherMake sure Pulley Direction shownBe removed in step Is attached as shownHold the Cable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyCable in the groove of the Pulley Identify the Press Cable 72. It is approximately Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Pulley and the pin on the Press Top FrameWrap the Press Cable 72 around a V-Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Pulley onto the 3/8 x 4 3/4 Bolt Route the Press Cable 72 through the Press102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatADJUSTMENTS, beginning on the following Adjustment Pin 40. Note The lip onLeg Press Plate 16 must be on the upper edge Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories to a Pulley Station Attaching the Curl PADTo change the setting of a weight stack, insert a Changing the Weight SettingWeight stack. Turn the bent end down LEG LOW Pulley ARM Press Weight Resistance ChartHigh Press LEG Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 Cable ID Chart Cable Diagrams70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No
Top Page Image Contents