Weider 831.159831 user manual To hold the Cable in the groove of the Pulley

Page 20

49.Wrap the Press Cable (72) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and

a Cable Trap (38) to the indicated hole in the

Press Upright (5) with a 3/8” x 3 3/4” Bolt (101), a 3/8” Washer (97) and a 3/8” Nylon Locknut (90).

Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

50.Route the Press Cable (72) through the opening in the Press Frame (17) and wrap the Cable around a 3 1/2” Pulley (35) in the direction shown.

Attach the 3 1/2” Pulley (35) and a Cable Trap

(38) to the indicated hole in the Press Frame (17)

with a 3/8” x 3 1/4” Bolt (104), a 3/8” Washer (97) and a 3/8” Nylon Locknut (90). Make sure the

Pulley is attached on the inside of the Press Frame. Make sure the Cable Trap is positioned

to hold the Cable in the groove of the Pulley.

51.Wrap the Press Cable (72) around a “V”-Pulley

(34)in the direction shown. Attach the Pulley and a Long Cable Trap (37) to the small tube on the

Press Upright (5) with a 3/8” x 3 1/4” Bolt (104), a 3/8” Washer (97) and a 3/8” Nylon Locknut (90).

Note: The small tube has four adjustment

holes. Attach the “V”-Pulley in the hole far- thest from the Upright. Make sure the Cable Trap is oriented as shown.

52.Wrap the Press Cable (72) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley to the indicated hole in the Press Frame (17) with a

3/8” x 3 1/4” Bolt (104), a 3/8” Washer (97), and a 3/8” Nylon Locknut (90). Make sure the Pulley is

attached on the inside of the Press Frame. Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

49

	90
	97
			35
		38	101
		38
		5
50
	72
	90
	35
	38		97
			97
		17	104
		17
51		90
		90
		97
		72

	5
34	37

104

52

104

72

97

38

35

90 17

20

Image 20

Contents Model No Serial No Serial Number DecalSEARS, Roebuck and CO Hoffman ESTATES, IL Patent PendingTable of Contents Important Precautions Decal Using the Power Stack weight systemBefore YOU Begin Assembly Cable AssemblyArm Assembly To open the parts bag for that stageTape over the head of each Bolt Frame AssemblyLocate and open the parts bag labeled 100 Onto the Bolts. Do not tighten the Nylon Locknuts yet109 Locknuts 86. Do not tighten the Nylon Locknuts yet YetDo not Tighten the Nylon Locknuts yet Into Press a 2 Square Inner Cap 67 into the Press Top FrameOn bottom On the Short Weight Tube On the bottomMust be behind the Center Top Frame, as shown in step Locknuts 90. Do not tighten the Nylon Locknuts yetNylon Locknuts yet Nylon JamnutsAssembly Pages 30 Identify the Butterfly Cable Pulley BAG 2. Remove one V-PulleyBag for identification of the Pro Pulleys Bracket onLabeled Pulley BAG Bracket On the back of the Butterfly UprightEd as shown Identify the Rear CableIdentify the Ab Cable 74. It is approximately Pulley and the pin on the Upright103 Large tabsMake sure Remove the 3 1/2 Pulleys 35 from the otherGroove of the Pulley Direction shown Be removed in stepPulley Is attached as shownCable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyHold the Cable in the groove of the Pulley Cable Trap 38 to the 3/8 x 4 3/4 Bolt With the 3/8 Nylon JamnutIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top FrameWrap the Press Cable 72 around a 3 1/2 Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a V-Pulley 102 3835 Route the Press Cable 72 through the PressPulley onto the 3/8 x 4 3/4 Bolt With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatLeg Press Plate 16 must be on the upper edge Adjustment Pin 40. Note The lip onADJUSTMENTS, beginning on the following Adjustments Attaching the Accessories to a Pulley StationAdjusting the LEG Press Plate Attaching the Curl PADWeight stack. Turn the bent end down Changing the Weight SettingTo change the setting of a weight stack, insert a Weight Resistance Chart High Press LEGLEG LOW Pulley ARM Press Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Cable DiagramsCable ID Chart Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No