Weider 831.159831 Identify the Ab Cable 74. It is approximately, 103, Large tabs, On this side

Page 15

29.Remove the 3 1/2” Pulleys (35) from a pair of pre- assembled Pulley Plates (32).

Wrap the Rear Cable (70) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and a Cable Trap (38) to the top hole in the pair of

Pulley Plates (32) with a 3/8” x 2” Bolt (93) and a 3/8” Nylon Locknut (90). Make sure the Cable

Trap is positioned to hold the Cable in the groove of the Pulley.

30.Wrap the Rear Cable (70) around a 4 1/2” Pulley

(36)in the direction shown. Attach the Pulley

inside the indicated bracket on the Center Top

Frame (8) with a 3/8” x 1 3/4” Bolt (94) and a 3/8” Nylon Locknut (90).

31. Attach the end of the Rear Cable (70) to a “U”- Bracket (33) with a 1/4” Washer (99) and a 1/4” Nylon Locknut (103).

Attach the “U”-Bracket (33) to the Short Weight

Tube (44) with a 5/16” x 1 3/4” Bolt (96) and a 5/16” Nylon Locknut (86).

32. Identify the Ab Cable (74). It is approximately

226 1/2” long, and it has a ball on one end and an eyelet on the other.

Wrap the Ab Cable (74) around a 3 1/2” Pulley

(35)as shown. Place two Pulley Covers (39) over the Pulley, so that the large tabs are on the side

shown. Attach the Pulley and Pulley Covers to the

Butterfly Upright (4) with a 3/8” x 3 3/4” Bolt (101), two 3/8” Washers (97), and a 3/8” Nylon Jamnut (92). Make sure the Cable is between

the Pulley and the pin on the Upright.

15

29
		70		93
				93
	90		35	32
			35

	32	38
	32
30	Bracket
	Bracket	90
		90
				36
				94
	8
			70
31
			70
			96
	33
	86			99
	86		103
			103
			44
32
92	97		Large tabs
92	97		on this side
		39
	Pin			39
				39
	4			101
	4	35		97
		35	74	97
			74

Image 15

Contents Patent Pending Model No Serial NoSerial Number Decal SEARS, Roebuck and CO Hoffman ESTATES, ILTable of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal To open the parts bag for that stage AssemblyCable Assembly Arm AssemblyFrame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the bottom On the Short Weight TubeNylon Jamnuts Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Locknuts yetAssembly Bracket on Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bag for identification of the Pro PulleysIdentify the Rear Cable Labeled Pulley BAGBracket On the back of the Butterfly Upright Ed as shownLarge tabs Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright 103Remove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Is attached as shown Direction shownBe removed in step PulleyIdentify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley Pulley and the pin on the Press Top Frame Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Identify the Press Cable 72. It is approximatelyTo hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat AssemblyAdjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Attaching the Curl PAD AdjustmentsAttaching the Accessories to a Pulley Station Adjusting the LEG Press PlateChanging the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down Lbs Left Top Weight Resistance ChartHigh Press LEG LEG LOW Pulley ARM PressTightening the Cables Troubleshooting and MaintenanceHole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No