Weider 831.159831 Remove the 3 1/2 Pulleys 35 from the other, Groove of the Pulley, Make sure

Page 16

33. Remove the 3 1/2” Pulleys (35) from the other		33
pair of pre-assembled Pulley Plates (32).		33
pair of pre-assembled Pulley Plates (32).
Wrap the Ab Cable (74) around a 3 1/2” Pulley
(35) in the direction shown. Attach the Pulley and
a Cable Trap (38) to the top hole in the pair of						74
Pulley Plates (32) with a 3/8” x 2” Bolt (93) and a
3/8” Nylon Locknut (90). Make sure the Cable						93
Trap is positioned to hold the Cable in the						93
Trap is positioned to hold the Cable in the
groove of the Pulley.		90			35	32
		90				32
			32
			32		38
					38
34. Wrap the Ab Cable (74) around a 3 1/2” Pulley		34
(35) in the direction shown. Attach the Pulley to		34
(35) in the direction shown. Attach the Pulley to
the Double “U”-Bracket (31) with a 3/8” x 1 3/4”		94
Bolt (94) and a 3/8” Nylon Locknut (90).		94
Bolt (94) and a 3/8” Nylon Locknut (90).
		31
		90
		35
		74
35. Wrap the Ab Cable (74) around a 3 1/2” Pulley		35
(35) in the direction shown. Attach the Pulley and		35
(35) in the direction shown. Attach the Pulley and					74
a Cable Trap (38) to the indicated bracket on the			93		74
a Cable Trap (38) to the indicated bracket on the
Butterfly Base (1) with a 3/8” x 2” Bolt (93) and a					35
Butterfly Base (1) with a 3/8” x 2” Bolt (93) and a					35
3/8” Nylon Locknut (90). Make sure the Cable					38
Trap is positioned to hold the Cable in the					38
Trap is positioned to hold the Cable in the
groove of the Pulley.
				1	90
36. Wrap the Ab Cable (74) around a 3 1/2” Pulley		36
(35) in the direction shown. Slide a Cable Trap		36
(35) in the direction shown. Slide a Cable Trap
(38) and the Pulley onto the 3/8” x 3 1/2” Carriage		35		92
Bolt (95) in the Butterfly Base (1). Secure the				92


Pulley with a 3/8” Nylon Jamnut (92).	Make sure	38
the Cable Trap is positioned to hold the Cable		74
in the groove of the Pulley.		74
in the groove of the Pulley.
		1	95

16

Image 16

Contents Model No Serial No Serial Number DecalSEARS, Roebuck and CO Hoffman ESTATES, IL Patent PendingTable of Contents Important Precautions Before YOU Begin Using the Power Stack weight systemDecal Assembly Cable AssemblyArm Assembly To open the parts bag for that stageLocate and open the parts bag labeled Frame AssemblyTape over the head of each Bolt 109 Onto the Bolts. Do not tighten the Nylon Locknuts yet100 Do not Tighten the Nylon Locknuts yet YetLocknuts 86. Do not tighten the Nylon Locknuts yet On bottom Press a 2 Square Inner Cap 67 into the Press Top FrameInto On the Short Weight Tube On the bottomMust be behind the Center Top Frame, as shown in step Locknuts 90. Do not tighten the Nylon Locknuts yetNylon Locknuts yet Nylon JamnutsAssembly Pages 30 Identify the Butterfly Cable Pulley BAG 2. Remove one V-PulleyBag for identification of the Pro Pulleys Bracket onLabeled Pulley BAG Bracket On the back of the Butterfly UprightEd as shown Identify the Rear CableIdentify the Ab Cable 74. It is approximately Pulley and the pin on the Upright103 Large tabsGroove of the Pulley Remove the 3 1/2 Pulleys 35 from the otherMake sure Direction shown Be removed in stepPulley Is attached as shownHold the Cable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyCable in the groove of the Pulley Cable Trap 38 to the 3/8 x 4 3/4 Bolt With the 3/8 Nylon JamnutIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top FrameWrap the Press Cable 72 around a V-Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Pulley onto the 3/8 x 4 3/4 Bolt Route the Press Cable 72 through the Press102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatADJUSTMENTS, beginning on the following Adjustment Pin 40. Note The lip onLeg Press Plate 16 must be on the upper edge Adjustments Attaching the Accessories to a Pulley StationAdjusting the LEG Press Plate Attaching the Curl PADTo change the setting of a weight stack, insert a Changing the Weight SettingWeight stack. Turn the bent end down Weight Resistance Chart High Press LEGLEG LOW Pulley ARM Press Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 Cable ID Chart Cable Diagrams70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No