Weider 831.159831 user manual With a 3/8 Nylon Jamnut 92. Make sure

Page 22

57.Remove the 3/8” Nylon Jamnut (92) used in step

53.Route the Press Cable (72) through the Press Frame (17).

Wrap the Press Cable (72) around a 3 1/2” Pulley (35) in the direction shown. Slide a Cable Trap

(38)and the Pulley onto the 3/8” x 4 3/4” Bolt

(102)in the bottom of the Press Upright (5). Properly tighten the 3/8” Nylon Jamnut (92) onto the Bolt. Make sure the Cable Trap is posi- tioned to hold the Cable in the groove of the Pulley.

58.Wrap the Press Cable (72) around a 3 1/2” Pulley

(35)in the direction shown. Slide a Cable Trap

(38)and the Pulley onto the 3/8” x 4” Carriage Bolt (112) in the Press Base (3). Secure the Pulley

with a 3/8” Nylon Jamnut (92). Make sure the

Cable Trap is positioned to hold the Cable in the groove of the Pulley.

59. Lay the Press Cable (72) in the bracket on the

Center Base (2). Attach a 3 1/2” Pulley (35) inside the bracket with a 3/8” x 1 3/4” Bolt (94) and a 3/8” Nylon Jamnut (92).

60.Wrap the Press Cable (72) around a 4 1/2” Pulley

(36)in the direction shown. Attach the Pulley inside the indicated bracket on the Center Top

Frame (8) with a 3/8” x 1 3/4” Bolt (94) and a 3/8” Nylon Locknut (90).

57
				38
				72
	5	102	35	92
	17		35
	17
58
	72	92
		35
		38
		112
		3
59
72	35		94
72

			92
			2
60		72
8	90	72
	90
			36
			36
			94

22

Image 22

Contents SEARS, Roebuck and CO Hoffman ESTATES, IL Model No Serial NoSerial Number Decal Patent PendingTable of Contents Important Precautions Before YOU Begin Using the Power Stack weight systemDecal Arm Assembly AssemblyCable Assembly To open the parts bag for that stageLocate and open the parts bag labeled Frame AssemblyTape over the head of each Bolt 109 Onto the Bolts. Do not tighten the Nylon Locknuts yet100 Do not Tighten the Nylon Locknuts yet YetLocknuts 86. Do not tighten the Nylon Locknuts yet On bottom Press a 2 Square Inner Cap 67 into the Press Top FrameInto On the Short Weight Tube On the bottomNylon Locknuts yet Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon JamnutsAssembly Bag for identification of the Pro Pulleys Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bracket onEd as shown Labeled Pulley BAGBracket On the back of the Butterfly Upright Identify the Rear Cable103 Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright Large tabsGroove of the Pulley Remove the 3 1/2 Pulleys 35 from the otherMake sure Pulley Direction shownBe removed in step Is attached as shownHold the Cable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyCable in the groove of the Pulley Identify the Press Cable 72. It is approximately Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Pulley and the pin on the Press Top FrameWrap the Press Cable 72 around a V-Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Pulley onto the 3/8 x 4 3/4 Bolt Route the Press Cable 72 through the Press102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatADJUSTMENTS, beginning on the following Adjustment Pin 40. Note The lip onLeg Press Plate 16 must be on the upper edge Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories to a Pulley Station Attaching the Curl PADTo change the setting of a weight stack, insert a Changing the Weight SettingWeight stack. Turn the bent end down LEG LOW Pulley ARM Press Weight Resistance ChartHigh Press LEG Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 Cable ID Chart Cable Diagrams70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No