Weider 831.159831 user manual Hole with the Bolt, Washer, and Nylon Locknut 104

Page 29

Slack can be removed from the Press Cable (72) by moving the “V”-Pulley (34) attached to the Press Seat Frame (12) closer to the Press Upright (5).

Remove the 3/8” x 4 1/4” Bolt (85), 3/8” Washer (97), and 3/8” Nylon Locknut (90) from the Press Seat

Frame (12), the “V”-Pulley (34), and the Long Cable Trap (37). Move the Pulley to a hole that is closer to

the Press Upright (5), one hole at a time, until the slack is removed. Reattach the Pulley and Cable Trap to the hole with the Bolt, Washer, and Nylon Locknut.

If there is still slack in the Press Cable (72), move the “V”-Pulley (34) attached to the small tube on the Press Upright (5) to a hole that is closer to the Upright.

Remove the 3/8” x 3 1/4” Bolt (104), 3/8” Washer (97), and 3/8” Nylon Locknut (90) from the Press Upright (5), the “V”-Pulley (34), and the Long Cable Trap (37). Move the Pulley to a hole that is closer to

the Press Upright, one hole at a time, until the slack is removed. Reattach the Pulley and Cable Trap to

the hole with the Bolt, Washer, and Nylon Locknut.

	85
	97
12	37
12
72	34
90
90
97
34
72	5
	104

If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

29

Image 29

Contents Serial Number Decal Model No Serial NoSEARS, Roebuck and CO Hoffman ESTATES, IL Patent PendingTable of Contents Important Precautions Decal Using the Power Stack weight systemBefore YOU Begin Cable Assembly AssemblyArm Assembly To open the parts bag for that stageTape over the head of each Bolt Frame AssemblyLocate and open the parts bag labeled 100 Onto the Bolts. Do not tighten the Nylon Locknuts yet109 Locknuts 86. Do not tighten the Nylon Locknuts yet YetDo not Tighten the Nylon Locknuts yet Into Press a 2 Square Inner Cap 67 into the Press Top FrameOn bottom On the bottom On the Short Weight TubeLocknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as shown in stepNylon Locknuts yet Nylon JamnutsAssembly Pulley BAG 2. Remove one V-Pulley Pages 30 Identify the Butterfly CableBag for identification of the Pro Pulleys Bracket onBracket On the back of the Butterfly Upright Labeled Pulley BAGEd as shown Identify the Rear CablePulley and the pin on the Upright Identify the Ab Cable 74. It is approximately103 Large tabsMake sure Remove the 3 1/2 Pulleys 35 from the otherGroove of the Pulley Be removed in step Direction shownPulley Is attached as shownCable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyHold the Cable in the groove of the Pulley With the 3/8 Nylon Jamnut Cable Trap 38 to the 3/8 x 4 3/4 BoltIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top FrameWrap the Press Cable 72 around a 3 1/2 Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a V-Pulley 102 3835 Route the Press Cable 72 through the PressPulley onto the 3/8 x 4 3/4 Bolt With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Adjustment Pin 40. Note The lip onADJUSTMENTS, beginning on the following Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADWeight stack. Turn the bent end down Changing the Weight SettingTo change the setting of a weight stack, insert a High Press LEG Weight Resistance ChartLEG LOW Pulley ARM Press Lbs Left TopTightening the Cables Troubleshooting and MaintenanceHole with the Bolt, Washer, and Nylon Locknut 104 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Cable DiagramsCable ID Chart Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No