Weider 831.159831 user manual

Page 35

5/16" x 1 3/4" Bolt (96)

5/16" x 1" Shoulder Bolt (84)

1” Tap Screw (80)

1/4" x 3/4" Bolt (98)

5/16" x 3" Bolt (107)

5/16" x 2 3/4" Shoulder Bolt (108)

3/8" x 3" Bolt (88)

3/8" x 3 1/4" Bolt (104)

3/8" x 3 1/2" Bolt (111)

3/8" x 3 1/2" Carriage Bolt (95)

3/8" x 3 3/4" Bolt (101)

3/8" x 4" Bolt (78)

3/8" x 4" Carriage Bolt (112)

3/8" x 4 1/4" Bolt (85)

3/8" x 4 3/4" Bolt (102)

3/8" x 8" Bolt (106)

Image 35

Contents Patent Pending Model No Serial NoSerial Number Decal SEARS, Roebuck and CO Hoffman ESTATES, ILTable of Contents Important Precautions Decal Using the Power Stack weight systemBefore YOU Begin To open the parts bag for that stage AssemblyCable Assembly Arm AssemblyTape over the head of each Bolt Frame AssemblyLocate and open the parts bag labeled 100 Onto the Bolts. Do not tighten the Nylon Locknuts yet109 Locknuts 86. Do not tighten the Nylon Locknuts yet YetDo not Tighten the Nylon Locknuts yet Into Press a 2 Square Inner Cap 67 into the Press Top FrameOn bottom On the bottom On the Short Weight TubeNylon Jamnuts Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Locknuts yetAssembly Bracket on Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bag for identification of the Pro PulleysIdentify the Rear Cable Labeled Pulley BAGBracket On the back of the Butterfly Upright Ed as shownLarge tabs Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright 103Make sure Remove the 3 1/2 Pulleys 35 from the otherGroove of the Pulley Is attached as shown Direction shownBe removed in step PulleyCable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyHold the Cable in the groove of the Pulley Pulley and the pin on the Press Top Frame Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Identify the Press Cable 72. It is approximatelyWrap the Press Cable 72 around a 3 1/2 Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a V-Pulley 102 3835 Route the Press Cable 72 through the PressPulley onto the 3/8 x 4 3/4 Bolt With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat AssemblyLeg Press Plate 16 must be on the upper edge Adjustment Pin 40. Note The lip onADJUSTMENTS, beginning on the following Attaching the Curl PAD AdjustmentsAttaching the Accessories to a Pulley Station Adjusting the LEG Press PlateWeight stack. Turn the bent end down Changing the Weight SettingTo change the setting of a weight stack, insert a Lbs Left Top Weight Resistance ChartHigh Press LEG LEG LOW Pulley ARM PressTightening the Cables Troubleshooting and MaintenanceHole with the Bolt, Washer, and Nylon Locknut 104 70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Cable DiagramsCable ID Chart Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No