Weider 831.159831 user manual Assembly

Page 12

Arm Assembly

 

18

92

11

 

 

18. Locate and open the parts bag labeled “ARM

 

 

67

 

 

 

 

104

ASSEMBLY.”

 

 

 

Press two 2” Square Inner Caps (67) into the

 

 

13

Lubricate

ends of the Leg Lever (13).

 

 

 

 

 

 

 

Lubricate a 3/8” x 3 1/4” Bolt (104). Attach the

 

67

 

Leg Lever (13) to the Butterfly Leg (11) with the

 

 

 

 

 

Bolt and a 3/8” Nylon Jamnut (92).

Do not over-

 

 

 

tighten the Nylon Jamnut; the Leg Lever must

 

 

 

 

be able to pivot easily.

 

 

 

 

19. Lubricate the 3/8” x 3” Bolt (88). Attach the Leg

19

 

 

Press Lever (14) to the Press Base (3) with the

 

 

 

 

 

Bolt and a 3/8” Nylon Locknut (90).

Do not over-

 

 

 

tighten the Nylon Locknut; the Leg Press

 

 

14

 

Lever must pivot easily.

 

 

 

 

 

 

 

 

 

 

Lubricate

 

 

 

 

88

3

 

 

 

 

 

 

 

 

90

20. See the inset drawing. Press a Plastic Bushing

 

20

 

 

(60) onto each welded tube on the Press Frame

 

 

 

 

 

 

 

(17). Slide the Pr ess Frame into place on the

 

 

 

 

Press Base (3). Note: This will be a tight fit.

 

 

 

The Plastic Bushings should fit onto each end

 

 

 

 

of the welded tubes in the Base.

 

 

106

 

Lubricate the 3/8” x 8” Bolt (106). Attach the

 

 

17

 

 

3

Press Frame (17) to the Press Base (3) with the

 

 

 

 

17

Bolt and a 3/8” Nylon Jamnut (92).

Do not over-

 

 

 

 

 

tighten the Nylon Jamnut; the Press Frame

 

 

Lubricate

92

must pivot easily.

 

 

 

 

 

 

60

21. Press a 1 3/4” Square Inner Cap (68) into the top

21

 

 

of a Press Arm (18). Press a 1” Round Inner Cap

 

 

 

 

 

(66) into the Press Arm.

 

 

18

 

Attach the Press Arm (18) to the Press Frame

 

 

 

 

(17) with two 5/16” x 2 1/2” Bolts (87) and two

 

 

 

5/16” Nylon Locknuts (86).

 

 

 

68

 

 

 

 

Repeat this step with the other Press Arm (18).

 

 

 

 

 

 

 

 

87

 

 

 

 

18

 

 

 

86

66

 

 

 

 

 

 

 

 

17

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model No Serial No Serial Number DecalSEARS, Roebuck and CO Hoffman ESTATES, IL Patent PendingTable of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal Assembly Cable AssemblyArm Assembly To open the parts bag for that stageFrame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the Short Weight Tube On the bottomMust be behind the Center Top Frame, as shown in step Locknuts 90. Do not tighten the Nylon Locknuts yetNylon Locknuts yet Nylon JamnutsAssembly Pages 30 Identify the Butterfly Cable Pulley BAG 2. Remove one V-PulleyBag for identification of the Pro Pulleys Bracket onLabeled Pulley BAG Bracket On the back of the Butterfly UprightEd as shown Identify the Rear CableIdentify the Ab Cable 74. It is approximately Pulley and the pin on the Upright103 Large tabsRemove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Direction shown Be removed in stepPulley Is attached as shownIdentify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley Cable Trap 38 to the 3/8 x 4 3/4 Bolt With the 3/8 Nylon JamnutIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top FrameTo hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatAdjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Adjustments Attaching the Accessories to a Pulley StationAdjusting the LEG Press Plate Attaching the Curl PADChanging the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down Weight Resistance Chart High Press LEGLEG LOW Pulley ARM Press Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No
Top Page Image Contents