Weider 831.159831 user manual Identify the Low Cable 71. It is approximately

Page 18

41.Locate the Weight Plate (48) that is attached to the bottom of the Bottom Weight (47).

See the inset drawing. Attach the end of the Ab

Cable (74) to the bottom of the Weight Plate (48)

with a 5/16” x 1 3/4” Bolt (96) and a 5/16” Nylon Locknut (86).

42.Remove a Pro Pulley (110) from the bag labeled “PULLEY BAG 2.”

Identify the Low Cable (71). It is approximately

142 1/8” long and it has a ball on one end and an eyelet on the other. Route the eyelet end through the slot in the cable guide on the Butterfly Base

(1).

Route the Low Cable (71) under the Pro Pulley (110). Attach the Pro Pulley and a Cable Trap

(38) to the bracket on the Butterfly Base (1) with

a 3/8” x 2” Bolt (93) and a 3/8” Nylon Locknut (90)Make. sure the Cable Trap is positioned to

hold the Cable in the groove of the Pulley.

43.Wrap the Low Cable (71) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and

a Cable Trap (38) to the indicated hole in the

Butterfly Upright (4) with a 3/8” x 4 3/4” Bolt (102)

and a 3/8” Nylon Jamnut (92). Note: Thread the

Jamnut only two turns onto the Bolt, another Pulley will be attached to the Bolt in step 45. Make sure the Cable Trap is positioned to

hold the Cable in the groove of the Pulley.

44.Wrap the Low Cable (71) over a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and a Cable Trap (38) to the forth set of holes from

the bottom in the Pulley Plates (32) with a 3/8” x

2” Bolt (93) and a 3/8” Nylon Locknut (90). Make sure the Cable Trap is positioned to hold the

Cable in the groove of the Pulley.

18

41
86
48
	96	47
74
42
93	110
	38
71
			90
		1
Cable
Guide
43	102
	102
		35
	71	38
		4	92
		4
44
32
90		93
38		35
38
	71

Image 18

Contents SEARS, Roebuck and CO Hoffman ESTATES, IL Model No Serial NoSerial Number Decal Patent PendingTable of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal Arm Assembly AssemblyCable Assembly To open the parts bag for that stageFrame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the Short Weight Tube On the bottomNylon Locknuts yet Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon JamnutsAssembly Bag for identification of the Pro Pulleys Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bracket onEd as shown Labeled Pulley BAGBracket On the back of the Butterfly Upright Identify the Rear Cable103 Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright Large tabsRemove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Pulley Direction shownBe removed in step Is attached as shownIdentify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley Identify the Press Cable 72. It is approximately Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Pulley and the pin on the Press Top FrameTo hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Seat Assembly Locate and open the parts bag labeled SeatAdjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Adjusting the LEG Press Plate AdjustmentsAttaching the Accessories to a Pulley Station Attaching the Curl PADChanging the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down LEG LOW Pulley ARM Press Weight Resistance ChartHigh Press LEG Lbs Left TopTroubleshooting and Maintenance Tightening the CablesHole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This Part Identification CHART-Model No R0502APage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No