Weider 831.159831 user manual Cable Trap 38 to the 3/8 x 4 3/4 Bolt, With the 3/8 Nylon Jamnut

Page 19

45. Remove the 3/8” Nylon Jamnut (92) from the

3/8” x 4 3/4” Bolt (102) inserted into the Butterfly Upright (4) in step 43.

Wrap the Low Cable (71) around a 3 1/2” Pulley (35) in the direction shown. Attach the Pulley and

a Cable Trap (38) to the 3/8” x 4 3/4” Bolt (102)

with the 3/8” Nylon Jamnut (92).	Make sure the
Cable Trap is positioned to hold the Cable in
the groove of the Pulley.

46.Attach the Low Cable (71) to the Leg Lever (13)

with a 5/16” x 2 3/4” Shoulder Bolt (108), a 5/16” Washer (100), and a 5/16” Nylon Jamnut (77).

47.Remove a Pro Pulley (110) from the bag labeled “PULLEY BAG 2.”

Identify the Press Cable (72). It is approximately

387 5/8” long and it has a ball on one end and a threaded shaft on the other.

Wrap the Press Cable (72) around the Pro Pulley

(110) in the direction shown. Attach the Pulley to

the Press Top Frame (9) with a 3/8” x 3 1/2” Bolt (111), a 3/8” Washer (97), and a 3/8” Nylon Jamnut (92). Make sure the Cable is between

the Pulley and the pin on the Press Top Frame.

48. Route the threaded end of the Press Cable (72)

around the 3 1/2” Pulley (35) that was attached to

the Press Top Frame (9) in step 16.	Make sure
the Cable Trap (38) is positioned to hold the
Cable in the groove of the Pulley.	Properly
tighten the 3/8” Nylon Locknut (not shown)
attached to the 3/8” x 4” Bolt (78).

19

45
		71
4
	102	38
	102	35	92
		35	92
46
100
77
13
			108
		71
47
92	97	9
		9
	Pin	110	111
			111

	72
48
			38
	9		35
	9		78
			78
			72

Image 19

Contents Patent Pending Model No Serial NoSerial Number Decal SEARS, Roebuck and CO Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin Using the Power Stack weight systemDecal To open the parts bag for that stage AssemblyCable Assembly Arm AssemblyLocate and open the parts bag labeled Frame AssemblyTape over the head of each Bolt 109 Onto the Bolts. Do not tighten the Nylon Locknuts yet100 Do not Tighten the Nylon Locknuts yet YetLocknuts 86. Do not tighten the Nylon Locknuts yet On bottom Press a 2 Square Inner Cap 67 into the Press Top FrameInto On the bottom On the Short Weight TubeNylon Jamnuts Must be behind the Center Top Frame, as shown in stepLocknuts 90. Do not tighten the Nylon Locknuts yet Nylon Locknuts yetAssembly Bracket on Pages 30 Identify the Butterfly CablePulley BAG 2. Remove one V-Pulley Bag for identification of the Pro PulleysIdentify the Rear Cable Labeled Pulley BAGBracket On the back of the Butterfly Upright Ed as shownLarge tabs Identify the Ab Cable 74. It is approximatelyPulley and the pin on the Upright 103Groove of the Pulley Remove the 3 1/2 Pulleys 35 from the otherMake sure Is attached as shown Direction shownBe removed in step PulleyHold the Cable in the groove of the Pulley Identify the Low Cable 71. It is approximatelyCable in the groove of the Pulley Pulley and the pin on the Press Top Frame Cable Trap 38 to the 3/8 x 4 3/4 BoltWith the 3/8 Nylon Jamnut Identify the Press Cable 72. It is approximatelyWrap the Press Cable 72 around a V-Pulley To hold the Cable in the groove of the PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Pulley onto the 3/8 x 4 3/4 Bolt Route the Press Cable 72 through the Press102 3835 With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat AssemblyADJUSTMENTS, beginning on the following Adjustment Pin 40. Note The lip onLeg Press Plate 16 must be on the upper edge Attaching the Curl PAD AdjustmentsAttaching the Accessories to a Pulley Station Adjusting the LEG Press PlateTo change the setting of a weight stack, insert a Changing the Weight SettingWeight stack. Turn the bent end down Lbs Left Top Weight Resistance ChartHigh Press LEG LEG LOW Pulley ARM PressTightening the Cables Troubleshooting and MaintenanceHole with the Bolt, Washer, and Nylon Locknut 104 Cable ID Chart Cable Diagrams70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable SEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY WarrantySEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No