Weider 831.159831 Route the Press Cable 72 through the Press, Pulley onto the 3/8 x 4 3/4 Bolt

Page 21

53.Wrap the Press Cable (72) around a 3 1/2” Pulley

(35)in the direction shown. Attach the Pulley and

a Cable Trap (38) to the indicated hole on the right side of the Press Upright (5) with a 3/8” x 4 3/4” Bolt (102) and a 3/8” Nylon Jamnut (92).

Note: Thread the Jamnut only two turns onto

the Bolt; another Pulley will be attached to the Bolt in step 57. Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

54. Route the Press Cable (72) through the Press

Frame (17) and around a 3 1/2” Pulley (35) as shown. Attach the Pulley and a Cable Trap (38) to

the indicated hole on the right side of the Leg Press Lever (14) with a 3/8” x 4 3/4” Bolt (102)

and a 3/8” Nylon Jamnut (92). Note: Thread the

Jamnut only two turns onto the Bolt; another Pulley will be attached to the Bolt in step 56. Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

55.Wrap the Press Cable (72) around a “V”-Pulley

(34)in the direction shown. Attach the Pulley and a Long Cable Trap (37) underneath the Press

Seat Frame (12) with a 3/8” x 4 1/4” Bolt (85), a 3/8” Washer (97), and a 3/8” Nylon Locknut (90).

Note: the Press Seat Frame has five adjust- ment holes. Attach the Pulley to the second hole from the Leg Press Lever (14). Make sure the Cable Trap is positioned to hold the Cable in the groove of the Pulley.

56.Remove the 3/8” Nylon Jamnut (92) used in step 54.

Wrap the Press Cable (72) around a 3 1/2” Pulley (35) in the direction shown. Slide a Cable Trap

(38)and the Pulley onto the 3/8” x 4 3/4” Bolt

(102)in the Leg Press Lever (14). Properly tight- en the 3/8” Nylon Jamnut (92) onto the Bolt.

Make sure the Cable Trap is positioned to

hold the Cable in the groove of the Pulley.

53
	102	92
	72	92
	72
	35	5
	35
	38
54
102	72
35	92
38
14
55
85
97
12	38
72	34
14	90
14
56
14
102
	92	72
	3835

21

Image 21

Contents Serial Number Decal Model No Serial NoSEARS, Roebuck and CO Hoffman ESTATES, IL Patent PendingTable of Contents Important Precautions Using the Power Stack weight system Before YOU BeginDecal Cable Assembly AssemblyArm Assembly To open the parts bag for that stageFrame Assembly Locate and open the parts bag labeledTape over the head of each Bolt Onto the Bolts. Do not tighten the Nylon Locknuts yet 109100 Yet Do not Tighten the Nylon Locknuts yetLocknuts 86. Do not tighten the Nylon Locknuts yet Press a 2 Square Inner Cap 67 into the Press Top Frame On bottomInto On the bottom On the Short Weight TubeLocknuts 90. Do not tighten the Nylon Locknuts yet Must be behind the Center Top Frame, as shown in stepNylon Locknuts yet Nylon JamnutsAssembly Pulley BAG 2. Remove one V-Pulley Pages 30 Identify the Butterfly CableBag for identification of the Pro Pulleys Bracket onBracket On the back of the Butterfly Upright Labeled Pulley BAGEd as shown Identify the Rear CablePulley and the pin on the Upright Identify the Ab Cable 74. It is approximately103 Large tabsRemove the 3 1/2 Pulleys 35 from the other Groove of the PulleyMake sure Be removed in step Direction shownPulley Is attached as shownIdentify the Low Cable 71. It is approximately Hold the Cable in the groove of the PulleyCable in the groove of the Pulley With the 3/8 Nylon Jamnut Cable Trap 38 to the 3/8 x 4 3/4 BoltIdentify the Press Cable 72. It is approximately Pulley and the pin on the Press Top FrameTo hold the Cable in the groove of the Pulley Wrap the Press Cable 72 around a V-PulleyWrap the Press Cable 72 around a 3 1/2 Pulley Route the Press Cable 72 through the Press Pulley onto the 3/8 x 4 3/4 Bolt102 3835 With a 3/8 Nylon Jamnut 92. Make sure Locate and open the parts bag labeled Seat Seat AssemblyAdjustment Pin 40. Note The lip on ADJUSTMENTS, beginning on the followingLeg Press Plate 16 must be on the upper edge Attaching the Accessories to a Pulley Station AdjustmentsAdjusting the LEG Press Plate Attaching the Curl PADChanging the Weight Setting To change the setting of a weight stack, insert aWeight stack. Turn the bent end down High Press LEG Weight Resistance ChartLEG LOW Pulley ARM Press Lbs Left TopTightening the Cables Troubleshooting and MaintenanceHole with the Bolt, Washer, and Nylon Locknut 104 Cable Diagrams Cable ID Chart70, 95 1/8 71, 142 1/8 74, 226 1/2 72, 387 5/8 Low Cable Rear Cable Ab Cable Butterfly Cable Full 90 DAY Warranty SEARS, Roebuck and CO., Hoffman ESTATES, ILSEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, IL This R0502A Part Identification CHART-Model NoPage Round Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Qty Description Key No. Qty Exploded DRAWING-Model No